Amazon Kindle Oasis 8Th Gen Battery Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 - 10 minutes

Sections

Back Panel
3 steps
Battery
6 steps

Flags

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel

Carefully wedge the plastic opening tool between the back panel and the device to free the clips holding the back panel and the device together.

Carefully wedge the plastic opening tool between the back panel and the device to free the clips holding the back panel and the device together.

1024

Step 2

Work your way around the back panel to free all the clips.
There are 5 clips on the long and thickest side of the oasis, and none on the others.

Work your way around the back panel to free all the clips.

There are 5 clips on the long and thickest side of the oasis, and none on the others.

Step 3

Carefully remove the back panel from the device.
Gently peel the back panel away from the adhesive, being mindful to keep the adhesive strip in good condition so that it can be used again.

Carefully remove the back panel from the device.

Gently peel the back panel away from the adhesive, being mindful to keep the adhesive strip in good condition so that it can be used again.

Step 4

              Battery

Using tweezers, lift the orange bridge connector off.
Place the tweezers in between the battery and the end of the bridge and lift upwards.

Using tweezers, lift the orange bridge connector off.

Place the tweezers in between the battery and the end of the bridge and lift upwards.

Step 5

Gently wedge the spudger under the battery starting from the left side, and slowly work the spudger around the edge to loosen the battery from the tape. Be careful not to rip the thin foil on the back of the battery.
Only use ESD safe tools when working on internal components of your device such as a spudger or opening tool.
It is not advised to use a metal spudger, as you could puncture the battery.

Gently wedge the spudger under the battery starting from the left side, and slowly work the spudger around the edge to loosen the battery from the tape. Be careful not to rip the thin foil on the back of the battery.

Only use ESD safe tools when working on internal components of your device such as a spudger or opening tool.

It is not advised to use a metal spudger, as you could puncture the battery.

Step 6

Lift the battery up using the spudger and use your fingers to slowly pull the battery off the adhesive.

Lift the battery up using the spudger and use your fingers to slowly pull the battery off the adhesive.

Step 7

Using the tweezers, gently lift the tape off of the Power bridge connector. If a new unit comes with a new piece of tape, remove entirely, if not remove and place one corner lightly face down on a clean surface to be used again.

Using the tweezers, gently lift the tape off of the Power bridge connector. If a new unit comes with a new piece of tape, remove entirely, if not remove and place one corner lightly face down on a clean surface to be used again.

Step 8

Once free of the adhesive and connectors, remove the old battery from the device.

Once free of the adhesive and connectors, remove the old battery from the device.

Step 9

              Install the new battery

Attach the new battery by inserting the end of the orange power connector (the end not attached to the battery) clips into a little socket on the device (it’s barely visible). You can tell when it clips in by the feel and sound. Make sure that when you put the new battery in, you first clip the connector in before you stick the tape down.
Be Aware: Your new battery might not be charged, so it may not power-on immediately! After replacing the battery, plug your Oasis in and let the battery charge to full capacity.

Attach the new battery by inserting the end of the orange power connector (the end not attached to the battery) clips into a little socket on the device (it’s barely visible). You can tell when it clips in by the feel and sound. Make sure that when you put the new battery in, you first clip the connector in before you stick the tape down.

Be Aware: Your new battery might not be charged, so it may not power-on immediately! After replacing the battery, plug your Oasis in and let the battery charge to full capacity.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      14 other people completed this guide.

Author

                                      with 11 other contributors

                    Mohamed Elzini

Member since: 09/27/2017

416 Reputation

                                      4 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team S16-G5, Eyestone Fall 2017                        

                                                  Member of USF Tampa, Team S16-G5, Eyestone Fall 2017 



                    USFT-EYESTONE-F17S16G5                     


                                            4 Members                     


                                            12 Guides authored

ALON GAZIT - Dec 2, 2018

Grate explanation. where can I find the battery? couldn’t find it anywhere

thanks

Ree - Mar 7, 2019

fabdelaere - Apr 14, 2019

Jim Price - Nov 11, 2019

WTH is a spudger?

Nat Whilk - Nov 15, 2019

You can find the battery here

https://www.nextbatteries.com/products/a…

890 mAH Li-Polymer 3.7V 61.60 x 53.32 x 2.78mm

Incorrect Tools#

Introduction#

What you need#

Team#

Incorrect Tools

Introduction

What you need

Team