Difficulty

Easy

Steps

10

Time Required

                          20 - 25 minutes

Sections

1

  • Car Mounting Clip
  • 10 steps

Flags

3

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackPhone Accessory

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Car Mounting Clip
  • In this case, the plastic connecting to the metal spring failed and caused one of the clip arms to break off.
  • Be sure to remove any pieces of broken plastic before you begin the fix.

In this case, the plastic connecting to the metal spring failed and caused one of the clip arms to break off.

Be sure to remove any pieces of broken plastic before you begin the fix.

1024

Step 2

  • Loosen the knob on the back of the phone holder.
  • Be sure to hold on to this knob as it will be integral to the rest of the fix.

Loosen the knob on the back of the phone holder.

Be sure to hold on to this knob as it will be integral to the rest of the fix.

Step 3

  • Once the knob is fully removed, the inside ball joint loosens up and can be moved around.
  • Remove the ball joint from the base of the phone holder.

Once the knob is fully removed, the inside ball joint loosens up and can be moved around.

Remove the ball joint from the base of the phone holder.

Step 4

  • Remove the tightening knob and set the broken clip aside or toss it in the trash.

Remove the tightening knob and set the broken clip aside or toss it in the trash.

Step 5

  • Locate the replacement clip that comes with the Andobil Easy Clip Car Mount Kit.
  • Put Tightening Knob on top of the new ball-jointed clip.

Locate the replacement clip that comes with the Andobil Easy Clip Car Mount Kit.

Put Tightening Knob on top of the new ball-jointed clip.

Step 6

  • Insert the new clipping mechanism into the back of the phone holder.

Insert the new clipping mechanism into the back of the phone holder.

Step 7

  • Open the Jaws using the knob on the top of the ball joint mechanism.

Open the Jaws using the knob on the top of the ball joint mechanism.

Step 8

  • Line up the jaws with the car vent and then use the knob on the bottom to close the jaws.

Line up the jaws with the car vent and then use the knob on the bottom to close the jaws.

Step 9

  • Tighten the knob on the back of the phone holder once you have adjusted it to the correct angle.

Tighten the knob on the back of the phone holder once you have adjusted it to the correct angle.

Step 10

  • Once you’ve finished tightening the knob, you are finished! This is the finished Product!

Once you’ve finished tightening the knob, you are finished! This is the finished Product!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Alexander Tavares

Member since: 03/24/2021

205 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       UMass Dartmouth, Team S2-G16, Riel Spring 2021                        

                                                  Member of UMass Dartmouth, Team S2-G16, Riel Spring 2021 



                    UMASSD-RIEL-S21S2G16                     


                                            1 Member                     


                                            3 Guides authored