Difficulty

Difficult

Steps

5

Time Required

                          9 - 20 minutes

Sections

1

  • Battery/Battery Wire
  • 5 steps

Flags

0

  • BackANKER SoundCore

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before attempting to replace anything, it is recommended that you look at this device’s troubleshooting guide.

If your battery cannot hold charge, has broken wires, or needs to be replaced for some reason, this guide will show you step by step how to replace/remove it. Soldering experience is needed.

You must be careful while replacing the battery. If the battery is having issues, it could have multiple dangerous attributes. Things like battery acid and exploding batteries are not fun to deal with, so approach this task with caution.

What you need

Step 1

              Battery/Battery Wire
  • Use the plastic opening tool to pry off the screen.
  • Remove the screen from the device.

Use the plastic opening tool to pry off the screen.

Remove the screen from the device.

1024

Step 2

  • Remove the eight 10 mm Phillips #0 screws from the speaker mount.
  • Remove the speaker mount gently.

Remove the eight 10 mm Phillips #0 screws from the speaker mount.

Remove the speaker mount gently.

Step 3

  • Remove the two 8mm Phillips #0 screws from the circuit board.
  • Remove the circuit board from its mount.

Remove the two 8mm Phillips #0 screws from the circuit board.

Remove the circuit board from its mount.

Step 4

  • Find the battery below the circuit board.
  • It is covered by fuzz that is the same color as the black casing, so it may be hard to see.
  • Pry the battery off using the iFixit opening tool.
  • Remove the battery from its holder.

Find the battery below the circuit board.

It is covered by fuzz that is the same color as the black casing, so it may be hard to see.

Pry the battery off using the iFixit opening tool.

Remove the battery from its holder.

Step 5

  • Desolder the battery wires.
  • Remove the battery and battery wire from the device.
  • For more information on soldering and desoldering connections, follow this guide.

Desolder the battery wires.

Remove the battery and battery wire from the device.

For more information on soldering and desoldering connections, follow this guide.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 3 other contributors 


                    Lucas Sandsor

Member since: 02/07/2020

280 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S22-G1, Regan Winter 2020                        

                                                  Member of Cal Poly, Team S22-G1, Regan Winter 2020 



                    CPSU-REGAN-W20S22G1                     


                                            5 Members                     


                                            5 Guides authored

limz555 - May 7, 2021

Reply

If a bt speaker battery died,the unit can’t power up by cable?

manfred.humphries - Sep 12, 2021

Reply

Nice guide… showed how to get the grill off… Unfortunately, my circuit board is epoxied in place.

Battery tests ok, but unit won’t turn on. Its going into the bag with other non-working electronics unless you have any ideas. The little speakers look very nice…

David Goodacre - Oct 31, 2021

Reply

My Anker works as long as it is plugged in (usb). As soon as the lead is removed, it dies.

Raghubir Roy L - Feb 22, 2022

Reply

Where do I get the new battery in India?