Apple Airport Extreme Model A1408 Wifi Card Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Back Pad
2 steps
Outer Case
2 steps
WiFi Card
3 steps

Flags

BackApple Airport Extreme Model A1408
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Pad

CAUTION: The heat gun and hair dryer can get very hot. Do not put your hands or any other body part too close to either device. Also, do not touch the back pad right after heating it.
Use a blow dryer or heat gun on a medium to high heat setting on the back pad to loosen the glue that attaches it to the device.

CAUTION: The heat gun and hair dryer can get very hot. Do not put your hands or any other body part too close to either device. Also, do not touch the back pad right after heating it.

Use a blow dryer or heat gun on a medium to high heat setting on the back pad to loosen the glue that attaches it to the device.

1024

Step 2

To avoid ripping the back pad, gently peel it back from one corner until the pad is completely off.
Use heat in areas where the glue is not loose enough.
You may need to reattach the back pad with double-sided tape if the glue is not tacky enough to stick the pad back on.

To avoid ripping the back pad, gently peel it back from one corner until the pad is completely off.

Use heat in areas where the glue is not loose enough.

You may need to reattach the back pad with double-sided tape if the glue is not tacky enough to stick the pad back on.

Step 3

              Outer Case

After removing the back pad, unscrew the five 5 mm Phillips #00 screws in the large, deep holes in the plastic casing. The plastic casing should come off easily after removing all the screws.
When installing the plastic back cover, ensure the lip is aligned with the ports on the back of the device.

After removing the back pad, unscrew the five 5 mm Phillips #00 screws in the large, deep holes in the plastic casing. The plastic casing should come off easily after removing all the screws.

When installing the plastic back cover, ensure the lip is aligned with the ports on the back of the device.

Step 4

Insert a narrow plastic opening tool into one of the notches. Apply moderate force to pull the metal casing from the plastic outer casing. You can use the rim of the outer case as leverage. You should hear a click when the metal casing detaches.
After you hear the click, remove the inner metal case from the outer case using your hands. It should not take very much force.

Insert a narrow plastic opening tool into one of the notches. Apply moderate force to pull the metal casing from the plastic outer casing. You can use the rim of the outer case as leverage. You should hear a click when the metal casing detaches.

After you hear the click, remove the inner metal case from the outer case using your hands. It should not take very much force.

Step 5

              WiFi Card

Remove the four wires coming from the antennas by pinching the cable at the tip and gently pulling up on it until it pops out of the socket.
Repeat for the remaining three wires.
You might need to wiggle the wire to free it from the socket.

Remove the four wires coming from the antennas by pinching the cable at the tip and gently pulling up on it until it pops out of the socket.

Repeat for the remaining three wires.

You might need to wiggle the wire to free it from the socket.

Step 6

Remove the 5 mm Phillips #00 screw from the right side of the WiFi card.

Remove the 5 mm Phillips #00 screw from the right side of the WiFi card.

Step 7

Do not pull the WiFi card directly up or you may damage the slot and the logic board.
Remove the WiFi card by gripping it on both sides and gently pulling it directly out of the slot.

Do not pull the WiFi card directly up or you may damage the slot and the logic board.

Remove the WiFi card by gripping it on both sides and gently pulling it directly out of the slot.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Ryan Frawley

Member since: 10/14/2014

355 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 10-37, Amido Fall 2014                        

                                                  Member of Cal Poly, Team 10-37, Amido Fall 2014 



                    CPSU-AMIDO-F14S10G37                     


                                            4 Members                     


                                            12 Guides authored

Robin Geerdens - Jun 20, 2016

Hi. By what wifi card can I replace the old one?

Introduction#

What you need#

Team#

Introduction

What you need

Team