Difficulty
Easy
Steps
14
Time Required
10 - 15 minutes
Sections
5
- Stand
- 1 step
- Panels
- 3 steps
- Metal EMI Shield
- 3 steps
- USB Port
- 3 steps
- ADC Cable
- 4 steps
Flags
0
BackApple Studio Display M7649
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Stand
- Lay the display facing down with the stand away from you.
- Remove the three size 2.0 hex screws on the swing arm and remove the swing arm as well as the plastic shield under it.
Lay the display facing down with the stand away from you.
Remove the three size 2.0 hex screws on the swing arm and remove the swing arm as well as the plastic shield under it.
1024
Step 2
Panels
- Remove the size 2.5 hex screws from each corner that connects the panels to the display and remove them.
Remove the size 2.5 hex screws from each corner that connects the panels to the display and remove them.
Step 3
- Rotate the display so the legs of the display are now facing you
- Grip the top of the clear panel and lift it upwards, and pull the ADC cable through the hole.
Rotate the display so the legs of the display are now facing you
Grip the top of the clear panel and lift it upwards, and pull the ADC cable through the hole.
Step 4
- Remove the grey back panel by lifting the bottom and pulling the ADC cable through the hole.
Remove the grey back panel by lifting the bottom and pulling the ADC cable through the hole.
Step 5
Metal EMI Shield
- The next layer will be a shiny metal panel, which might have some stickers. Make sure to remove these stickers.
The next layer will be a shiny metal panel, which might have some stickers. Make sure to remove these stickers.
Step 6
- Now locate and remove the lone Phillips screw holding the EMI shield to the display
Now locate and remove the lone Phillips screw holding the EMI shield to the display
Step 7
- Now that the screw has been removed, slide the panel towards your body and lift it out.
- You may need to remove the clear USB port cover to remove the metal EMI shield.
Now that the screw has been removed, slide the panel towards your body and lift it out.
You may need to remove the clear USB port cover to remove the metal EMI shield.
Step 8
USB Port
- To remove the USB port, remove these four screws holding down the port and metal brackets.
- There may be a zip tie you need to cut that is attaching the USB unit to the display
To remove the USB port, remove these four screws holding down the port and metal brackets.
There may be a zip tie you need to cut that is attaching the USB unit to the display
Step 9
- Remove the cable from the logic board that is connecting the USB port.
Remove the cable from the logic board that is connecting the USB port.
Step 10
- Remove the USB port
Remove the USB port
Step 11
ADC Cable
- Remove these four screws holding down the base of the swing arm to the display and remove it
Remove these four screws holding down the base of the swing arm to the display and remove it
Step 12
- Remove the four screws holding down the ADC cable to the display
Remove the four screws holding down the ADC cable to the display
Step 13
- Remove the three connections that connects the ADC assembly to the logic board and screen
Remove the three connections that connects the ADC assembly to the logic board and screen
Step 14
- Remove and replace the ADC cable assembly.
Remove and replace the ADC cable assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Andrew Tsao
Member since: 01/19/2010
171 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 3-20, Maness Winter 2010
Member of Cal Poly, Team 3-20, Maness Winter 2010
CPSU-MANESS-W10S3G20
4 Members
15 Guides authored
Cali Red - Mar 4, 2022
Reply
What are the two red wires and two black wires ?
