Difficulty
Moderate
Steps
7
Time Required
Suggest a time??
Sections
2
- Lower Case
- 4 steps
- AirPort Card
- 3 steps
Flags
0
BackApple TV 1st Generation
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Flip the Apple TV over so that the bottom of the unit is facing up.
- You need to remove the rubber base to get access to the screws.
- Starting at one side of the device, use a hairdryer or a heat gun to soften the adhesive holding the rubber base in place.
- The rubber base will be hot after heating, take extreme caution while proceeding to avoid personal injury.
- While the adhesive is still warm, peel the bottom of the rubber base upwards to detach it from the metal plate.
- The rubber base can tear if the adhesive hasn’t been softened enough.
- Repeat the procedure described above until the rubber base has been completely removed.
Flip the Apple TV over so that the bottom of the unit is facing up.
You need to remove the rubber base to get access to the screws.
Starting at one side of the device, use a hairdryer or a heat gun to soften the adhesive holding the rubber base in place.
The rubber base will be hot after heating, take extreme caution while proceeding to avoid personal injury.
While the adhesive is still warm, peel the bottom of the rubber base upwards to detach it from the metal plate.
The rubber base can tear if the adhesive hasn’t been softened enough.
Repeat the procedure described above until the rubber base has been completely removed.
1024
Step 2
- Remove the four T10 Torx screws that secure the lower case to the upper case.
Remove the four T10 Torx screws that secure the lower case to the upper case.
Step 3
- Carefully lift the lower case from the upper case enough to allow access to the internals of the Apple TV.
- Be aware that the hard drive is physically attached to the lower case and that a ribbon cable runs from the drive to the logic board in the upper case.
Carefully lift the lower case from the upper case enough to allow access to the internals of the Apple TV.
Be aware that the hard drive is physically attached to the lower case and that a ribbon cable runs from the drive to the logic board in the upper case.
Step 4
- Carefully pull the hard drive data cable straight up from its socket on the logic board.
- During reassembly, make sure the hard drive data cable is firmly seated in its socket on the logic board; otherwise, during boot-up you will see a flashing question mark “?”.
Carefully pull the hard drive data cable straight up from its socket on the logic board.
During reassembly, make sure the hard drive data cable is firmly seated in its socket on the logic board; otherwise, during boot-up you will see a flashing question mark “?”.
Step 5
AirPort Card
- Pry the AirPort antenna cables straight up from their sockets on the logic board.
Pry the AirPort antenna cables straight up from their sockets on the logic board.
Step 6
- Remove the single T8 Torx screw securing the AirPort card to the logic board.
Remove the single T8 Torx screw securing the AirPort card to the logic board.
Step 7
- Cautiously lift the AirPort card and pull it straight away. Slide it from its socket on the logic board.
Cautiously lift the AirPort card and pull it straight away. Slide it from its socket on the logic board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
11 other people completed this guide.
Author
with 7 other contributors
ropel
Member since: 11/11/2009
113 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 18-5, Maness Fall 2009
Member of Cal Poly, Team 18-5, Maness Fall 2009
CPSU-MANESS-F09S18G5
5 Members
6 Guides authored
