Difficulty
Moderate
Steps
12
Time Required
30 minutes - 1 hour
Sections
3
- Lid
- 4 steps
- Heating Element/ Thermostat
- 6 steps
- Control Module
- 2 steps
Flags
0
BackAroma ARC-914SBD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lid
- Begin by removing the condensation catcher to expose the screw. Pinch the condensation catcher from both sides and pull.
Begin by removing the condensation catcher to expose the screw. Pinch the condensation catcher from both sides and pull.
1024
Step 2
- Remove the screw that was behind the condensation catcher using a Phillips head screwdriver, size PH2.
Remove the screw that was behind the condensation catcher using a Phillips head screwdriver, size PH2.
Step 3
- Remove the piece that was held by the screw by pulling out from the top, then pulling up. This will expose the hinges for the lid.
Remove the piece that was held by the screw by pulling out from the top, then pulling up. This will expose the hinges for the lid.
Step 4
- To remove the hinges, rotate the bottom of the rod upwards, then push inwards to pull them out. Repeat the process for both sides. This will allow the lid to be removed.
To remove the hinges, rotate the bottom of the rod upwards, then push inwards to pull them out. Repeat the process for both sides. This will allow the lid to be removed.
Step 5
Heating Element/ Thermostat
- Locate the piece on the black plastic trim that is opposite from where the hinges were. Carefully, pry this piece from the bottom to get the tab from behind the stainless steel to in front of the steel as shown.
Locate the piece on the black plastic trim that is opposite from where the hinges were. Carefully, pry this piece from the bottom to get the tab from behind the stainless steel to in front of the steel as shown.
Step 6
- Next, you must remove the upper black trim which is connected to the inside liner with tabs. To do this you must hold the interior walls still, while rotating the trim so that the tabs line up with the slots. (tabs cannot be seen at this point, pics are to give you an idea of what you cannot see inside the device)
Next, you must remove the upper black trim which is connected to the inside liner with tabs. To do this you must hold the interior walls still, while rotating the trim so that the tabs line up with the slots. (tabs cannot be seen at this point, pics are to give you an idea of what you cannot see inside the device)
Step 7
- Using a Phillips head screwdriver, size PH2, remove the screws from the control module to expose wired connections.
Using a Phillips head screwdriver, size PH2, remove the screws from the control module to expose wired connections.
Step 8
- Unplug thermostat from control module
Unplug thermostat from control module
Step 9
- Remove red and blue wires from heating element to fully detach from control module. This is done by removing the screws on the heating element terminals using a Phillips head screwdriver, size PH2.
Remove red and blue wires from heating element to fully detach from control module. This is done by removing the screws on the heating element terminals using a Phillips head screwdriver, size PH2.
Step 10
- Again, using a Phillips head screwdriver, size PH2, remove the three screws holding the heating element assembly to the bowl. This will remove the heating element and the thermostat.
Again, using a Phillips head screwdriver, size PH2, remove the three screws holding the heating element assembly to the bowl. This will remove the heating element and the thermostat.
Step 11
Control Module
- Unplug the interface from the control module
Unplug the interface from the control module
Step 12
- Unplug the power from the control module
Unplug the power from the control module
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 5 other contributors
Brandon Nieves
Member since: 09/04/2015
956 Reputation
8 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 2-3, Sullivan Fall 2015
Member of USF Tampa, Team 2-3, Sullivan Fall 2015
USFT-SULLIVAN-F15S2G3
3 Members
8 Guides authored
Harriot Smyth - Nov 14, 2016
Reply
I found the problem inside the unit, a blown thermal fuse on the neutral side of the power. The inside of this unit is nothing like the pictures, but the part up to removing the black rim was accurate. This unit is an SB and apparently a lesser model of the above.
Dav e - Jan 31, 2017
Reply
Thanks for this, very helpful. I only needed to remove the loud, horrible beeper (mission accomplished, woohoo!) although the really hard part for some reason was rotating the tabbed black ring independently of the inside liner. Coudn’t get it to budge AT ALL, as if they were glued together. I could only rotate them as a unit inside the housing. After way too long working at this, I ended up wedging a flathead into the crevice between the ring and liner, from the inside, at the two points where I could see the tabs through the hole on the outside, then just twisted the screwdriver and snapped off the tabs one at a time. There are two more tabs on the other side of the ring, but these just slide out once the first two are gone, and the liner can be easily removed. When reassembling, the black trim fits quite snugly back onto the liner, so the unit feels as solid as it did before the operation. Thanks again!
James DeLabar - May 31, 2017
Dave,
I also plan to remove beeper, did you just cut it out or un-solder it? any issues?
thanks
David DiGiacomo - Dec 11, 2018
I’m not Dave, but I used a vacuum desoldering tool to remove the beeper, which was easy. I think there would have been enough room to cut it out also. The only hard part was getting the black ring off and then back on.
Pantulu Chinta - Oct 31, 2017
Reply
I want one trolley module for ARC 3000SB. Where can I get. How much I have to. Pay for it approximately.
Email id pantulu.chinta@gmail.com
