Aroma Arc 914Sbd Heating Element Thermostat Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          30 minutes - 1 hour            

Sections

2

• Lid
• 4 steps
• Heating Element/ Thermostat
• 6 steps

Flags

0

• BackAroma ARC-914SBD

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Lid               

• Begin by removing the condensation catcher to expose the screw. Pinch the condensation catcher from both sides and pull.

Begin by removing the condensation catcher to expose the screw. Pinch the condensation catcher from both sides and pull.

1024

Step 2

• Remove the screw that was behind the condensation catcher using a Phillips head screwdriver, size PH2.

Remove the screw that was behind the condensation catcher using a Phillips head screwdriver, size PH2.

Step 3

• Remove the piece that was held by the screw by pulling out from the top, then pulling up. This will expose the hinges for the lid.

Remove the piece that was held by the screw by pulling out from the top, then pulling up. This will expose the hinges for the lid.

Step 4

• To remove the hinges, rotate the bottom of the rod upwards, then push inwards to pull them out. Repeat the process for both sides. This will allow the lid to be removed.

To remove the hinges, rotate the bottom of the rod upwards, then push inwards to pull them out. Repeat the process for both sides. This will allow the lid to be removed.

Step 5

              Heating Element/ Thermostat               

• Locate the piece on the black plastic trim that is opposite from where the hinges were. Carefully, pry this piece from the bottom to get the tab from behind the stainless steel to in front of the steel as shown.

Locate the piece on the black plastic trim that is opposite from where the hinges were. Carefully, pry this piece from the bottom to get the tab from behind the stainless steel to in front of the steel as shown.

Step 6

• Next, you must remove the upper black trim which is connected to the inside liner with tabs. To do this you must hold the interior walls still, while rotating the trim so that the tabs line up with the slots. (tabs cannot be seen at this point, pics are to give you an idea of what you cannot see inside the device)

Next, you must remove the upper black trim which is connected to the inside liner with tabs. To do this you must hold the interior walls still, while rotating the trim so that the tabs line up with the slots. (tabs cannot be seen at this point, pics are to give you an idea of what you cannot see inside the device)

Step 7

• Using a Phillips head screwdriver, size PH2, remove the screws from the control module to expose wired connections.

Using a Phillips head screwdriver, size PH2, remove the screws from the control module to expose wired connections.

Step 8

• Unplug thermostat from control module

Unplug thermostat from control module

Step 9

• Remove red and blue wires from heating element to fully detach from control module. This is done by removing the screws on the heating element terminals using a Phillips head screwdriver, size PH2.

Remove red and blue wires from heating element to fully detach from control module. This is done by removing the screws on the heating element terminals using a Phillips head screwdriver, size PH2.

Step 10

• Again, using a Phillips head screwdriver, size PH2, remove the three screws holding the heating element assembly to the bowl. This will remove the heating element and the thermostat.

Again, using a Phillips head screwdriver, size PH2, remove the three screws holding the heating element assembly to the bowl. This will remove the heating element and the thermostat.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 5 other contributors 

                    Brandon Nieves                     

Member since: 09/04/2015

956 Reputation

                                      8 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       USF Tampa, Team 2-3, Sullivan Fall 2015                        

                                                  Member of USF Tampa, Team 2-3, Sullivan Fall 2015 



                    USFT-SULLIVAN-F15S2G3                     


                                            3 Members                     


                                            8 Guides authored                     

4forums - Sep 25, 2022

Reply

Where do you get a replacement thermostat?