Difficulty
Moderate
Steps
11
Time Required
10 - 30 minutes
Sections
2
- Keyboard
- 5 steps
- Screen
- 6 steps
Flags
0
BackAsus Chromebook C101P
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Keyboard
- Flip the Chromebook so that the bottom is facing up.
- Remove the nine T5 Torx screws.
Flip the Chromebook so that the bottom is facing up.
Remove the nine T5 Torx screws.
1024
Step 2
- Remove the four rubber grips on the bottom side of the Chromebook using an opening tool.
Remove the four rubber grips on the bottom side of the Chromebook using an opening tool.
Step 3
- Remove the four black screws where the rubber grips were.
Remove the four black screws where the rubber grips were.
Step 4
- Reorient the Chromebook so the right side is facing upwards.
- Wedge an opening tool or spudger between the keyboard (upper case) and the lower case of the bottom portion of the Chromebook.
Reorient the Chromebook so the right side is facing upwards.
Wedge an opening tool or spudger between the keyboard (upper case) and the lower case of the bottom portion of the Chromebook.
Step 5
- Pull back the black lever on the base of the cable. While pulling back, take your tweezers and pull back on the large ribbon cable.
- Pull back the black lever on the base of the cable. While pulling back, take your tweezers and pull back on the small ribbon cable.
- Separate the keyboard from the rest of the laptop.
Pull back the black lever on the base of the cable. While pulling back, take your tweezers and pull back on the large ribbon cable.
Pull back the black lever on the base of the cable. While pulling back, take your tweezers and pull back on the small ribbon cable.
Separate the keyboard from the rest of the laptop.
Step 6
Screen
- Detach the the screen cables from the motherboard using a pair of tweezers.
- Peel off the tape or seal to easily remove the screen cables.
Detach the the screen cables from the motherboard using a pair of tweezers.
Peel off the tape or seal to easily remove the screen cables.
Step 7
- Remove the Phillips 00 screws from the hinges.
Remove the Phillips 00 screws from the hinges.
Step 8
- Angle the hinge as shown and use a T5 Torx screwdriver to remove the hinge screws.
Angle the hinge as shown and use a T5 Torx screwdriver to remove the hinge screws.
Step 9
- Pry open the hinge by using the iFixit opening tool.
Pry open the hinge by using the iFixit opening tool.
Step 10
- Use the iFixit opening tool to pop out the black rubber grips near the bottom of the screen.
- Use a Phillips 00 screwdriver to remove the screws beneath the rubber grips.
Use the iFixit opening tool to pop out the black rubber grips near the bottom of the screen.
Use a Phillips 00 screwdriver to remove the screws beneath the rubber grips.
Step 11
- Use the iFixit opening tool to pry around the screen.
- Use the space between the screen and the hinge to prop it up.
- Once open, slide the wires that are in the hinge out. The screen should now be fully detached from the case.
Use the iFixit opening tool to pry around the screen.
Use the space between the screen and the hinge to prop it up.
Once open, slide the wires that are in the hinge out. The screen should now be fully detached from the case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Dan Sysopha
Member since: 10/25/2019
341 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
UMass Dartmouth, Team S1-G2, O'Connell Fall 2019
Member of UMass Dartmouth, Team S1-G2, O'Connell Fall 2019
UMASSD-O'CONNELL-F19S1G2
2 Members
5 Guides authored
