Difficulty
Moderate
Steps
18
Time Required
35 minutes
Sections
2
- Palm Rest Assembly
- 8 steps
- LCD Screen
- 10 steps
Flags
0
BackAsus Chromebook C201
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Palm Rest Assembly
- Flip the laptop upside down with the rear end of the computer away from you.
Flip the laptop upside down with the rear end of the computer away from you.
1024
Step 2
- Remove the two rear rubber feet by using one of the small, blue plastic spudgers.
Remove the two rear rubber feet by using one of the small, blue plastic spudgers.
Step 3
- Use the J0 screwdriver to remove the eight 5mm black screws on the bottom of the laptop, which includes the two that were hidden under the rear rubber feet.
Use the J0 screwdriver to remove the eight 5mm black screws on the bottom of the laptop, which includes the two that were hidden under the rear rubber feet.
Step 4
- Turn the laptop on its side. Use a small, blue opening tool to pry the keyboard cover and laptop apart. Begin from the top right, next to the power button, and slowly work your way around to the opposite side until the keyboard cover is detached.
Turn the laptop on its side. Use a small, blue opening tool to pry the keyboard cover and laptop apart. Begin from the top right, next to the power button, and slowly work your way around to the opposite side until the keyboard cover is detached.
Step 5
- Gently flip the keyboard cover away from the laptop. Rest it safely upside down so the cables are not strained and are easily accessible.
Gently flip the keyboard cover away from the laptop. Rest it safely upside down so the cables are not strained and are easily accessible.
Step 6
- Use the metal spudger to gently pry up the small tabs that are clamping down on the keyboard cables.
Use the metal spudger to gently pry up the small tabs that are clamping down on the keyboard cables.
Step 7
- Carefully pull the keyboard cables out of the connecting ports that are attached to the motherboard.
Carefully pull the keyboard cables out of the connecting ports that are attached to the motherboard.
Step 8
- Remove the keyboard cover and safely place it somewhere face down.
Remove the keyboard cover and safely place it somewhere face down.
Step 9
LCD Screen
- Locate the LCD cable and its connector which is located in the upper left hand corner of the computer. Carefully flip up the tiny tab and safely remove the cable using precision tweezers.
Locate the LCD cable and its connector which is located in the upper left hand corner of the computer. Carefully flip up the tiny tab and safely remove the cable using precision tweezers.
Step 10
- Disconnect the black and white cables located near the screen hinge.
Disconnect the black and white cables located near the screen hinge.
Step 11
- Remove the 6, 4mm silver screws from the hinges attaching the LCD to the laptop using the J0 Phillips screwdriver.
Remove the 6, 4mm silver screws from the hinges attaching the LCD to the laptop using the J0 Phillips screwdriver.
Step 12
- Turn the hinges to an upright position.
Turn the hinges to an upright position.
Step 13
- Carefully pop the LCD screen assembly out of the laptop case.
Carefully pop the LCD screen assembly out of the laptop case.
Step 14
- Remove the silver cover.
- Make sure to put the cover back in right side (longer side) up when re-installing
Remove the silver cover.
Make sure to put the cover back in right side (longer side) up when re-installing
Step 15
- Use a blue plastic spudger to snap the LCD cover off, working the spudger around the perimeter and completely remove the cover.
Use a blue plastic spudger to snap the LCD cover off, working the spudger around the perimeter and completely remove the cover.
Step 16
- Remove the 4, 3mm silver corner screws holding in the LCD.
Remove the 4, 3mm silver corner screws holding in the LCD.
Step 17
- Remove the left hinge by unscrewing the two 3mm large Phillips head screws.
- Unscrew the one 3mm small Phillips head screw.
Remove the left hinge by unscrewing the two 3mm large Phillips head screws.
Unscrew the one 3mm small Phillips head screw.
Step 18
- Carefully lift the screen. Gently unravel and unplug the LCD cord.
Carefully lift the screen. Gently unravel and unplug the LCD cord.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 5 other contributors
Taylor Allen
Member since: 02/09/2016
327 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
USF Tampa, Team 2-51, Cagle Spring 2016
Member of USF Tampa, Team 2-51, Cagle Spring 2016
USFT-CAGLE-S16S2G51
4 Members
10 Guides authored
