Difficulty
Moderate
Steps
8
Time Required
25 - 30 minutes
Sections
1
- Charging Port
- 8 steps
Flags
0
BackAsus Chromebook Flip C100P
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Charging Port
- Remove three of the rubber feet on the bottom cover with a plastic or metal spudger.
Remove three of the rubber feet on the bottom cover with a plastic or metal spudger.
1024
Step 2
- Remove the five screws from beneath the rubber feet using a Phillips #0 screwdriver.
- The first 1.9mm screw is located under the front right foot, the second 1.9mm screw and third 2.3mm screw are located under the rear right foot, and the fourth and fifth 2.3mm screws are located under the rear left foot.
Remove the five screws from beneath the rubber feet using a Phillips #0 screwdriver.
The first 1.9mm screw is located under the front right foot, the second 1.9mm screw and third 2.3mm screw are located under the rear right foot, and the fourth and fifth 2.3mm screws are located under the rear left foot.
Step 3
- Remove the nine bottom cover screws using a T5 screwdriver.
- Set apart the 6mm screw in the rear middle of the bottom cover from the the other eight 3mm screws, as it is longer than them.
Remove the nine bottom cover screws using a T5 screwdriver.
Set apart the 6mm screw in the rear middle of the bottom cover from the the other eight 3mm screws, as it is longer than them.
Step 4
- Pry the palm rest assembly apart from the bottom cover using a spudger. This step may require extra power.
- Once the palm rest has been separated from the bottom cover, pull it away from the screen, rather than away from yourself.
Pry the palm rest assembly apart from the bottom cover using a spudger. This step may require extra power.
Once the palm rest has been separated from the bottom cover, pull it away from the screen, rather than away from yourself.
Step 5
- Disconnect the touchpad cable and the keyboard cable on the palm rest assembly from the motherboard using the pointed end of a plastic spudger.
Disconnect the touchpad cable and the keyboard cable on the palm rest assembly from the motherboard using the pointed end of a plastic spudger.
Step 6
- Disconnect the DC jack cable and the battery cable from the motherboard using tweezers, the pointed end of a plastic spudger, or by simply pulling the cables apart from the motherboard with your fingers.
Disconnect the DC jack cable and the battery cable from the motherboard using tweezers, the pointed end of a plastic spudger, or by simply pulling the cables apart from the motherboard with your fingers.
Step 7
- Remove the two 2.7mm screws using the Phillips #0 screwdriver.
Remove the two 2.7mm screws using the Phillips #0 screwdriver.
Step 8
- Using a pair of tweezers or your fingers, lift up the charging cable and remove the charging port.
Using a pair of tweezers or your fingers, lift up the charging cable and remove the charging port.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 3 other contributors
Sid Yadav
Member since: 03/19/2018
424 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
Baylor, Team S5-G2, Williams Spring 2018
Member of Baylor, Team S5-G2, Williams Spring 2018
BU-WILLIAMS-S18S5G2
3 Members
8 Guides authored
Alexandra Miller - May 5, 2021
Reply
I just did this but now when I turn it on there is no picture on the computer. I had to change the charging port because my cats knocked over a water glass. The charging port was successful because the light was on. Amy troubleshooting?
