Difficulty
Moderate
Steps
5
Time Required
30 minutes
Sections
1
- LCD Digitizer w/ Bezel
- 5 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackASUS Chromebook Flip C302CA-DHM4
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Remove Display
- Lay the Chromebook flat.
- Remove the two screws at the bottom of the display bezel.
- Using the Jimmy or a plastic opening tool, gently pry open the top and side edges of the display cover.
Lay the Chromebook flat.
Remove the two screws at the bottom of the display bezel.
Using the Jimmy or a plastic opening tool, gently pry open the top and side edges of the display cover.
1024
Step 2
Disconnect Display Wiring
- Pull back the clear tape with the Angled Precision Tweezers. Also pull back the black tape.
- Disconnect the LCD cable by gently pulling it back towards the hinge with the plastic spudger.
Pull back the clear tape with the Angled Precision Tweezers. Also pull back the black tape.
Disconnect the LCD cable by gently pulling it back towards the hinge with the plastic spudger.
Step 3
Disconnect Digitizer
- To remove the thin cables for the digitizer, you must first open the fastener by flipping the off-white plastic edge closest to the LCD towards the outside edge of the frame.
- Once the fasteners have been opened, use two spudgers to remove each cable by unfolding and dragging them back towards the outside edge of the frame.
- To release circuit board, use a spudger tool to pry the gray clip back. Gently pull up on the left edge of the circuit board.
- The right edge of the circuit board is glued down. Using a spudger, pry up on the right edge to free it from the frame display.
To remove the thin cables for the digitizer, you must first open the fastener by flipping the off-white plastic edge closest to the LCD towards the outside edge of the frame.
Once the fasteners have been opened, use two spudgers to remove each cable by unfolding and dragging them back towards the outside edge of the frame.
To release circuit board, use a spudger tool to pry the gray clip back. Gently pull up on the left edge of the circuit board.
The right edge of the circuit board is glued down. Using a spudger, pry up on the right edge to free it from the frame display.
Step 4
Release Digitizer and Webcam Wiring
- Use the Angled Tweezer to gently remove the brown wire from the channel. This wire travels from the hinge around the bottom edge and connects to the digitizer and webcam.
Use the Angled Tweezer to gently remove the brown wire from the channel. This wire travels from the hinge around the bottom edge and connects to the digitizer and webcam.
Step 5
Replace and Reassemble Display
- Follow the previous steps to replace the display just as you’ve removed it. Take care to ensure the LCD and Digitizer/Webcam cables are properly seated in the channels before sealing the lid.
- When the laptop lid is sealed, the hinge edge will lay uniformly flat.
Follow the previous steps to replace the display just as you’ve removed it. Take care to ensure the LCD and Digitizer/Webcam cables are properly seated in the channels before sealing the lid.
When the laptop lid is sealed, the hinge edge will lay uniformly flat.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 1 other contributor
Dave Van Allen
Member since: 05/07/2017
202 Reputation
1 Guide authored
Badges:
5
+2 more badges
Kev in - May 7, 2020
Reply
Thanks, took a bit of searching to actually find a replacement screen! eventually got one sent from china via eBay, this guide was invaluable , thank you so much.
