Difficulty
Moderate
Steps
10
Time Required
15 - 30 minutes
Sections
2
- Back Panel
- 6 steps
- microSD Card Slot, HDMI Port, and Headphone Jack
- 4 steps
Flags
0
BackASUS Eee Pad Transformer
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Use T5 Torx Screwdriver to remove two 4.5 millimeter T5 screws on either side of the port on the bottom of the tablet.
Use T5 Torx Screwdriver to remove two 4.5 millimeter T5 screws on either side of the port on the bottom of the tablet.
1024
Step 2
- Use the Plastic Opening Tool to pry between the main tablet body and the outer rim casing. Remove the outer rim casing by prying all the way around the device and pulling the rim upward.
- The physical buttons are located on the outside of the rim on the right side, proceed with the guide to locate internal buttons.
Use the Plastic Opening Tool to pry between the main tablet body and the outer rim casing. Remove the outer rim casing by prying all the way around the device and pulling the rim upward.
The physical buttons are located on the outside of the rim on the right side, proceed with the guide to locate internal buttons.
Step 3
- Remove the four 2 millimeter Phillips #00 screws at the corners of the tablet.
Remove the four 2 millimeter Phillips #00 screws at the corners of the tablet.
Step 4
- Use a Phillips #00 Screwdriver to remove the three 3 millimeter screws securing the front panel to the back panel found above the camera area, on the top portion of the tablet.
Use a Phillips #00 Screwdriver to remove the three 3 millimeter screws securing the front panel to the back panel found above the camera area, on the top portion of the tablet.
Step 5
- Use a Phillips #00 Screwdriver to remove the three 3 millimeter screws securing the front panel to the back panel found on the bottom portion of the tablet near the port.
Use a Phillips #00 Screwdriver to remove the three 3 millimeter screws securing the front panel to the back panel found on the bottom portion of the tablet near the port.
Step 6
- Remove back panel by pulling away from the remaining device.
Remove back panel by pulling away from the remaining device.
Step 7
Remove screws
- Use a Phillips #00 Screwdriver to remove the three 3 millimeter screws found on back side of the device to the left of the rear-facing camera.
Use a Phillips #00 Screwdriver to remove the three 3 millimeter screws found on back side of the device to the left of the rear-facing camera.
Step 8
Lift up flaps
- Use Plastic Opening Tool to lift up the two white flaps.
Use Plastic Opening Tool to lift up the two white flaps.
Step 9
Remove wire clip
- Use Tweezers to unclip the wire from the back panel by pulling straight outward from the device.
Use Tweezers to unclip the wire from the back panel by pulling straight outward from the device.
Step 10
Pull out panel
- Pull microSD Card, HDMI Port, and Headphone Jack panel straight out from tablet.
- Use Plastic Opening Tool to remove the wire on the panel by hooking it around the white clip and pulling straight out from the panel.
Pull microSD Card, HDMI Port, and Headphone Jack panel straight out from tablet.
Use Plastic Opening Tool to remove the wire on the panel by hooking it around the white clip and pulling straight out from the panel.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 4 other contributors
Sandy Babich
Member since: 09/23/2014
1,823 Reputation
5 Guides authored
Badges:
18
+15 more badges
Team
Cal Poly, Team 13-9, Forte Fall 2014
Member of Cal Poly, Team 13-9, Forte Fall 2014
CPSU-FORTE-F14S13G9
5 Members
12 Guides authored
