Asus Eee Pc 1005Peb Keyboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Battery
4 steps
Keyboard
5 steps

Flags

BackAsus Eee PC 1005PEB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Start by placing the laptop upside-down on a flat surface.
Find the two clips on the back portion of the laptop.

Start by placing the laptop upside-down on a flat surface.

Find the two clips on the back portion of the laptop.

1024

Step 2

Using your finger, push the clip labeled with a “1” on the laptop from the lock position to unlock position.
This clip will hold itself, so after you move it to the unlock position you can remove your finger.

Using your finger, push the clip labeled with a “1” on the laptop from the lock position to unlock position.

This clip will hold itself, so after you move it to the unlock position you can remove your finger.

Step 3

Using your finger, push and hold the pin indicated by a “2” on the laptop from the lock to unlock position.
While holding this pin in the unlock position, use your other hand to pull the battery horizontally away from the laptop.
When the pins on the battery that reach towards the laptop are away from the laptop, you can release the “2” clip.

Using your finger, push and hold the pin indicated by a “2” on the laptop from the lock to unlock position.

While holding this pin in the unlock position, use your other hand to pull the battery horizontally away from the laptop.

When the pins on the battery that reach towards the laptop are away from the laptop, you can release the “2” clip.

Step 4

Using both hands, pull the battery horizontally away from the laptop.

Using both hands, pull the battery horizontally away from the laptop.

Step 5

              Keyboard

Face the laptop so the 4 silver “clips” along the middle of the battery cartridge are in front of you.

Face the laptop so the 4 silver “clips” along the middle of the battery cartridge are in front of you.

Step 6

Using the wide opening tool, unhook each clip from its original position by pulling the clip towards you.
Repeat for all four of the clips.

Using the wide opening tool, unhook each clip from its original position by pulling the clip towards you.

Repeat for all four of the clips.

Step 7

Turn the laptop right side up and lift the lid.
Insert the flat end of the spudger into the small gap between the top of the keyboard and the plastic of the laptop.
Using the spudger as leverage, lift the keyboard up from the rest of the laptop.
Run the spudger across the seam until the entire top edge is exposed. The two sides of the keyboard should also pop up in this process.

Turn the laptop right side up and lift the lid.

Insert the flat end of the spudger into the small gap between the top of the keyboard and the plastic of the laptop.

Using the spudger as leverage, lift the keyboard up from the rest of the laptop.

Run the spudger across the seam until the entire top edge is exposed. The two sides of the keyboard should also pop up in this process.

Step 8

The keyboard should now lift from the base of the laptop.
Do not lift the keyboard up to quickly or too hard, since a ribbon cable is still attached to the keyboard and doing so could break it.

The keyboard should now lift from the base of the laptop.

Do not lift the keyboard up to quickly or too hard, since a ribbon cable is still attached to the keyboard and doing so could break it.

Step 9

Using the pointed end of the spudger tool, disconnect the ribbon cable that extends from the bottom of the keyboard to the computer by pushing on the connections of the cable.
Once the ribbon cable is disconnected, the keyboard can be fully removed by lifting it away from the laptop.

Using the pointed end of the spudger tool, disconnect the ribbon cable that extends from the bottom of the keyboard to the computer by pushing on the connections of the cable.

Once the ribbon cable is disconnected, the keyboard can be fully removed by lifting it away from the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 6 other contributors

                    Aaron Arenas

Member since: 04/20/2014

745 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 13-32, Maness Spring 2014                        

                                                  Member of Cal Poly, Team 13-32, Maness Spring 2014 



                    CPSU-MANESS-S14S13G32                     


                                            5 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team