Difficulty

Moderate

Steps

9

Time Required

                          20 - 30 minutes

Sections

2

  • Battery
  • 3 steps
  • LCD Screen
  • 6 steps

Flags

4

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackAsus Eee PC 1008ha

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Using the plastic opening tool, carefully pry the top panel from the base.

Using the plastic opening tool, carefully pry the top panel from the base.

1024

Step 2

  • Lift the side of the keyboard.
  • Disconnect the attached ribbon located underneath the keyboard.
  • Place your index finger in the hole on the right side of the keyboard tray and lift the tray.

Lift the side of the keyboard.

Disconnect the attached ribbon located underneath the keyboard.

Place your index finger in the hole on the right side of the keyboard tray and lift the tray.

Step 3

  • Use your fingers to lift the battery and gently disconnect the wires from the base.

Use your fingers to lift the battery and gently disconnect the wires from the base.

Step 4

              LCD Screen
  • Using the Phillips #00 screwdriver, unscrew the 4mm screws from the rightmost circuit board.
  • Carefully pull the circuit board away from side of device base.

Using the Phillips #00 screwdriver, unscrew the 4mm screws from the rightmost circuit board.

Carefully pull the circuit board away from side of device base.

Step 5

  • Using the Phillips #00 screwdriver, unscrew the 4mm screws attaching screen to base from both sides.
  • Gently lift the screen portion from the base.

Using the Phillips #00 screwdriver, unscrew the 4mm screws attaching screen to base from both sides.

Gently lift the screen portion from the base.

Step 6

  • Using the Plastic Opening Tool, pry the six small chits from the face of the screen portion.
  • Using the Phillips #00 screwdriver, unscrew the two 2mm and four 4mm screws from underneath the chits.

Using the Plastic Opening Tool, pry the six small chits from the face of the screen portion.

Using the Phillips #00 screwdriver, unscrew the two 2mm and four 4mm screws from underneath the chits.

Step 7

  • Slide the Plastic Opening Tool under the edge of the screen bezel to release the front panel of the screen.

Slide the Plastic Opening Tool under the edge of the screen bezel to release the front panel of the screen.

Step 8

  • Using the Phillips #00 screwdriver, unscrew the 2mm screws from the perimeter of the screen.
  • Use your fingers to hold the screen and carefully lift it from the base.

Using the Phillips #00 screwdriver, unscrew the 2mm screws from the perimeter of the screen.

Use your fingers to hold the screen and carefully lift it from the base.

Step 9

  • Use your fingers to peel back the adhesive tape located on the back of the screen.
  • Disconnect the wire from the screen.

Use your fingers to peel back the adhesive tape located on the back of the screen.

Disconnect the wire from the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 9 other contributors 


                    Michael Dooley

Member since: 04/18/2013

138 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 21-52, Johann Spring 2013                        

                                                  Member of Cal Poly, Team 21-52, Johann Spring 2013 



                    CPSU-JOHANN-S13S21G52                     


                                            4 Members                     


                                            11 Guides authored