Difficulty
Moderate
Steps
9
Time Required
15 - 20 minutes
Sections
2
- Optical Drive
- 3 steps
- Trackpad Button
- 6 steps
Flags
0
BackAsus G74SX-BBK7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Optical Drive
- Using a flathead screwdriver, spudger, or large coin such as a quarter, remove the 13mm screw on the bottom of the laptop.
- Take off the back panel.
Using a flathead screwdriver, spudger, or large coin such as a quarter, remove the 13mm screw on the bottom of the laptop.
Take off the back panel.
1024
Step 2
- Now, unscrew and remove the 6mm Phillips #0 screw next to the optical drive.
Now, unscrew and remove the 6mm Phillips #0 screw next to the optical drive.
Step 3
- Lastly, use a plastic opening tool to remove the optical drive from its slot.
Lastly, use a plastic opening tool to remove the optical drive from its slot.
Step 4
Trackpad Button
- Remove the two 6mm Phillips #0 screws that were previously covered by the optical drive using a Phillips #0 screwdriver.
Remove the two 6mm Phillips #0 screws that were previously covered by the optical drive using a Phillips #0 screwdriver.
Step 5
- First, remove the five 10mm Phillips #0 screws from the back of the computer near the top.
- Remove all eighteen 6mm Phillips #0 screws from the bottom of the computer.
- Some of the screws are set very deeply in the back case - you will need a long and narrow screwdriver to remove them.
First, remove the five 10mm Phillips #0 screws from the back of the computer near the top.
Remove all eighteen 6mm Phillips #0 screws from the bottom of the computer.
Some of the screws are set very deeply in the back case - you will need a long and narrow screwdriver to remove them.
Step 6
- Next, pry open back plastic cover using a metal spudger.
- Unscrew the four 10mm Phillips #0 screws under the cover.
Next, pry open back plastic cover using a metal spudger.
Unscrew the four 10mm Phillips #0 screws under the cover.
Step 7
- Lay laptop opened and completely flat.
- Using the metal spudger, slowly pry open the front main panel by going around each side.
- Lift the top panel out, pulling the cable strips out of their sockets. These will be reattached later.
- Be careful when lifting the top panel. There are cable strips attached to the motherboard that need to be removed.
Lay laptop opened and completely flat.
Using the metal spudger, slowly pry open the front main panel by going around each side.
Lift the top panel out, pulling the cable strips out of their sockets. These will be reattached later.
Be careful when lifting the top panel. There are cable strips attached to the motherboard that need to be removed.
Step 8
- After separating the main panel and the motherboard, unscrew two 6mm Phillips #0 screws.
- Remove the mouse button.
After separating the main panel and the motherboard, unscrew two 6mm Phillips #0 screws.
Remove the mouse button.
Step 9
- To reconnect the motherboard and main panel, insert strips back to their corresponding location.
- To do this, first remove the tape and open up the tab. Plug in the strip and and close the tab.
- It may be helpful to have someone help you hold the main panel while you reconnect the strips.
To reconnect the motherboard and main panel, insert strips back to their corresponding location.
To do this, first remove the tape and open up the tab. Plug in the strip and and close the tab.
It may be helpful to have someone help you hold the main panel while you reconnect the strips.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Ryan Lawrence
Member since: 04/14/2015
611 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 5-10, Maness Spring 2015
Member of Cal Poly, Team 5-10, Maness Spring 2015
CPSU-MANESS-S15S5G10
4 Members
6 Guides authored
websmiths - Jun 22, 2017
Reply
Where did you find the part?