Difficulty
Moderate
Steps
12
Time Required
10 - 15 minutes
Sections
3
- Back Panel
- 4 steps
- Keyboard
- 2 steps
- Track Pad
- 6 steps
Flags
0
BackASUS K200MA-DS01T
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- With the opening facing you, flip the laptop over and remove the following screws from the back panel:
- Six 4mm Phillips screws using a Phillips #0 screwdriver.
- One 12mm Phillips screw in the center using a Phillips #0 screwdriver.
With the opening facing you, flip the laptop over and remove the following screws from the back panel:
Six 4mm Phillips screws using a Phillips #0 screwdriver.
One 12mm Phillips screw in the center using a Phillips #0 screwdriver.
1024
Step 2
- Using a plastic spudger, remove the two rubber stoppers closest to the hinge to reveal the screws underneath.
Using a plastic spudger, remove the two rubber stoppers closest to the hinge to reveal the screws underneath.
Step 3
- Remove the following screws:
- Two 4mm Phillips screws using a Phillips #0 screwdriver.
Remove the following screws:
Two 4mm Phillips screws using a Phillips #0 screwdriver.
Step 4
- Using a plastic spudger (and a fair amount of force), pry the back panel up from the keyboard to separate.
- You may have to use one spudger to wedge between the back panel and keyboard while using another to pry it open in a different spot.
Using a plastic spudger (and a fair amount of force), pry the back panel up from the keyboard to separate.
You may have to use one spudger to wedge between the back panel and keyboard while using another to pry it open in a different spot.
Step 5
Keyboard
- To disconnect the keyboard connectors from keyboard and back panel, gently pull wide keyboard connector out.
- Gently pull the narrow connector away from the keyboard.
To disconnect the keyboard connectors from keyboard and back panel, gently pull wide keyboard connector out.
Gently pull the narrow connector away from the keyboard.
Step 6
- Now that the keyboard connectors are unplugged, pull the keyboard off and away from the back panel hinges.
Now that the keyboard connectors are unplugged, pull the keyboard off and away from the back panel hinges.
Step 7
Track Pad
- Lift the keyboard connector from the keyboard.
Lift the keyboard connector from the keyboard.
Step 8
- Lift the foil sheet.
Lift the foil sheet.
Step 9
- Remove the following screws:
- Eight 3 mm screws using Phillips screwdriver.
- Be sure to remove the screw underneath the keyboard connector.
Eight 3 mm screws using Phillips screwdriver.
Be sure to remove the screw underneath the keyboard connector.
Step 10
- Remove the following screws:
- Two 2 mm screws using a Phillips #00 screwdriver.
Two 2 mm screws using a Phillips #00 screwdriver.
Step 11
- Using a plastic spudger, remove the metal plate.
Using a plastic spudger, remove the metal plate.
Step 12
- Flip the keyboard over.
- Using a plastic spudger, pry the track pad off the plastic piece underneath.
- Don’t be afraid to use some force in this step because the track pad and the plastic piece are glued together.
Flip the keyboard over.
Using a plastic spudger, pry the track pad off the plastic piece underneath.
Don’t be afraid to use some force in this step because the track pad and the plastic piece are glued together.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Terrinda
Member since: 09/17/2018
526 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
CSU Fullerton, Team S2-G5, Bruce Fall 2018
Member of CSU Fullerton, Team S2-G5, Bruce Fall 2018
CSUF-BRUCE-F18S2G5
4 Members
7 Guides authored
