Difficulty

Very easy

Steps

12

Time Required

                          1 - 5 minutes

Sections

4

  • Battery
  • 4 steps
  • Speakers
  • 3 steps
  • Motherboard
  • 3 steps
  • Front and Rear cameras.
  • 2 steps

Flags

3

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

  • BackASUS MeMo Pad FHD10

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure that the device is turned off as a precaution.
  • Unplug the charger and remove any memory card you may have in the device.
  • Wedge the plastic opening tool between the front and back cover on every side.
  • Slide the plastic opening tool back and forth to make sure that the back cover is disconnected.
  • Once disconnected, remove the back cover from the device screen.

Make sure that the device is turned off as a precaution.

Unplug the charger and remove any memory card you may have in the device.

Wedge the plastic opening tool between the front and back cover on every side.

Slide the plastic opening tool back and forth to make sure that the back cover is disconnected.

Once disconnected, remove the back cover from the device screen.

1024

Step 2

  • Remove the protective copper sticker and all tape fixed on the device.
  • Using tweezers, remove the ribbon cable from their connections attached to the motherboard.
  • While using the tweezers, make sure to use minimum force and precision to avoid damaging any components.

Remove the protective copper sticker and all tape fixed on the device.

Using tweezers, remove the ribbon cable from their connections attached to the motherboard.

While using the tweezers, make sure to use minimum force and precision to avoid damaging any components.

Step 3

  • Remove the four 2 mm Phillips #00 screws holding the battery tray in place.

Remove the four 2 mm Phillips #00 screws holding the battery tray in place.

Step 4

  • Locate the battery cable attached to the motherboard. Using the same technique used on the ribbons, do the same with the battery.
  • Remove the battery from the device. Once removed, use the plastic tool to separate the metal frame from the battery.
  • When separating the metal frame, be sure to hold on in the center as the battery is two separate cells.

Locate the battery cable attached to the motherboard. Using the same technique used on the ribbons, do the same with the battery.

Remove the battery from the device. Once removed, use the plastic tool to separate the metal frame from the battery.

When separating the metal frame, be sure to hold on in the center as the battery is two separate cells.

Step 5

              Speakers
  • Remove three screws using a Phillips #00 screwdriver.

Remove three screws using a Phillips #00 screwdriver.

Step 6

  • The two speakers are located on opposite sides of the device. Both are long black pieces with connections to the motherboard.
  • Unplug the speaker cables from their connections on the motherboard gently by using tweezers.

The two speakers are located on opposite sides of the device. Both are long black pieces with connections to the motherboard.

Unplug the speaker cables from their connections on the motherboard gently by using tweezers.

Step 7

  • Gently use your hands to remove the speakers.

Gently use your hands to remove the speakers.

Step 8

              Motherboard
  • Remove the five screws using a Phillips #00 screwdriver.

Remove the five screws using a Phillips #00 screwdriver.

Step 9

  • Carefully disconnect the cord that connects the on/off button to the motherboard
  • Peel back the electrical tape holding the connections of the motherboard down to the frame of the device.

Carefully disconnect the cord that connects the on/off button to the motherboard

Peel back the electrical tape holding the connections of the motherboard down to the frame of the device.

Step 10

  • Use your hands to remove the motherboard from the device.

Use your hands to remove the motherboard from the device.

Step 11

              Front and Rear cameras.
  • Identify the location of front and rear cameras on the motherboard.

Identify the location of front and rear cameras on the motherboard.

Step 12

  • The front and rear cameras can be removed by pulling them out gently using hands.

The front and rear cameras can be removed by pulling them out gently using hands.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Dmitry

Member since: 01/21/2015

391 Reputation

                                      3 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       USF Tampa, Team 9-5, Blackwell Winter 2015                        

                                                  Member of USF Tampa, Team 9-5, Blackwell Winter 2015 



                    USFT-BLACKWELL-W15S9G5                     


                                            4 Members                     


                                            10 Guides authored