Difficulty
Moderate
Steps
8
Time Required
15 minutes
Sections
2
- Battery
- 4 steps
- GPS Antennna
- 4 steps
Flags
1
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
BackAsus MeMO Pad HD 7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove Rear Panel
- Carefully remove the back panel by using a plastic opening tool to remove the panel off the device.
- Pull the back panel away from the device.
- The volume buttons can fall out of the case. Pay attention so as not to lose them.
Carefully remove the back panel by using a plastic opening tool to remove the panel off the device.
Pull the back panel away from the device.
The volume buttons can fall out of the case. Pay attention so as not to lose them.
1024
Step 2
- Unlock the ZIF connectors on the data cables.
- Raise the white locking tabs by lifting their upper edge - furthest from the battery - they hinge across the width of the connector.
- Remove the cable from its slot by gently pulling downward on the tabs.
- Check that the touchscreen cables are fully seated when reassembling or touchscreen may have unresponsive areas.
Unlock the ZIF connectors on the data cables.
Raise the white locking tabs by lifting their upper edge - furthest from the battery - they hinge across the width of the connector.
Remove the cable from its slot by gently pulling downward on the tabs.
Check that the touchscreen cables are fully seated when reassembling or touchscreen may have unresponsive areas.
Step 3
- Locate the battery connector by following the wires that come from the top right of the battery. To disconnect the battery just lift up gently on the wires. Use a spudger or blue plastic opening tool to gently lift the wires if it is hard to get a grip.
Locate the battery connector by following the wires that come from the top right of the battery. To disconnect the battery just lift up gently on the wires. Use a spudger or blue plastic opening tool to gently lift the wires if it is hard to get a grip.
Step 4
Remove Battery
- Using a spudger carefully pry the battery up. It is glued down so slight pressure may be needed.
- The battery has a soft casing, be careful not to tear the battery casing as chemicals could leak out.
Using a spudger carefully pry the battery up. It is glued down so slight pressure may be needed.
The battery has a soft casing, be careful not to tear the battery casing as chemicals could leak out.
Step 5
GPS Antennna
- Pry the GPS Antenna cable straight up using a spudger or similar prying tool. It will be the grey wire that runs up the right side of the device coming from the speaker housing up to the motherboard.
Pry the GPS Antenna cable straight up using a spudger or similar prying tool. It will be the grey wire that runs up the right side of the device coming from the speaker housing up to the motherboard.
Step 6
- Unscrew two Philip’s #000 2 mm screws located on the left and right side of the speaker housing.
Unscrew two Philip’s #000 2 mm screws located on the left and right side of the speaker housing.
Step 7
- Using a spudger carefully, pry the GPS antenna from the bottom of the speaker housing.
Using a spudger carefully, pry the GPS antenna from the bottom of the speaker housing.
Step 8
- Peel the copper tape holding the GPS Antenna down to the inside of the device using caution not to tear the tape.
Peel the copper tape holding the GPS Antenna down to the inside of the device using caution not to tear the tape.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 7 other contributors
Julien Daigle
Member since: 01/20/2015
1,235 Reputation
5 Guides authored
Badges:
18
+15 more badges
Team
USF Tampa, Team 11-3, Blackwell Winter 2015
Member of USF Tampa, Team 11-3, Blackwell Winter 2015
USFT-BLACKWELL-W15S11G3
4 Members
5 Guides authored