Asus Memo Pad Hd 7 Speaker Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
4 steps
Speaker Assembly
4 steps

Flags

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

BackAsus MeMO Pad HD 7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Remove Rear Panel

Carefully remove the back panel by using a plastic opening tool to remove the panel off the device.
Pull the back panel away from the device.
The volume buttons can fall out of the case. Pay attention so as not to lose them.

Carefully remove the back panel by using a plastic opening tool to remove the panel off the device.

Pull the back panel away from the device.

The volume buttons can fall out of the case. Pay attention so as not to lose them.

1024

Step 2

Unlock the ZIF connectors on the data cables.
Raise the white locking tabs by lifting their upper edge - furthest from the battery - they hinge across the width of the connector.
Remove the cable from its slot by gently pulling downward on the tabs.
Check that the touchscreen cables are fully seated when reassembling or touchscreen may have unresponsive areas.

Unlock the ZIF connectors on the data cables.

Raise the white locking tabs by lifting their upper edge - furthest from the battery - they hinge across the width of the connector.

Remove the cable from its slot by gently pulling downward on the tabs.

Check that the touchscreen cables are fully seated when reassembling or touchscreen may have unresponsive areas.

Step 3

Locate the battery connector by following the wires that come from the top right of the battery. To disconnect the battery just lift up gently on the wires. Use a spudger or blue plastic opening tool to gently lift the wires if it is hard to get a grip.

Locate the battery connector by following the wires that come from the top right of the battery. To disconnect the battery just lift up gently on the wires. Use a spudger or blue plastic opening tool to gently lift the wires if it is hard to get a grip.

Step 4

              Remove Battery

Using a spudger carefully pry the battery up. It is glued down so slight pressure may be needed.
The battery has a soft casing, be careful not to tear the battery casing as chemicals could leak out.

Using a spudger carefully pry the battery up. It is glued down so slight pressure may be needed.

The battery has a soft casing, be careful not to tear the battery casing as chemicals could leak out.

Step 5

              Speaker Assembly

Unscrew two Philip’s #000 2 mm screws located on the left and right side of the speaker housing.

Unscrew two Philip’s #000 2 mm screws located on the left and right side of the speaker housing.

Step 6

Locate the speaker wires to the left side of the battery. Remove the connector by pulling up gently or prying with a tool if you can not get a good grip.

Locate the speaker wires to the left side of the battery. Remove the connector by pulling up gently or prying with a tool if you can not get a good grip.

Step 7

Pry the GPS Antenna cable straight up using a spudger or similar prying tool. It will be the grey wire that runs up the right side of the device coming from the speaker housing up to the logic board.

Pry the GPS Antenna cable straight up using a spudger or similar prying tool. It will be the grey wire that runs up the right side of the device coming from the speaker housing up to the logic board.

Step 8

Using a spudger, carefully pry the GPS antenna from the bottom of the speaker housing.
With the GPS antenna removed from the bottom of the speaker housing it can be removed from the device.

Using a spudger, carefully pry the GPS antenna from the bottom of the speaker housing.

With the GPS antenna removed from the bottom of the speaker housing it can be removed from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 5 other contributors

                    Julien Daigle

Member since: 01/20/2015

1,235 Reputation

                                      5 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges

Team

                       USF Tampa, Team 11-3, Blackwell Winter 2015                        

                                                  Member of USF Tampa, Team 11-3, Blackwell Winter 2015 



                    USFT-BLACKWELL-W15S11G3                     


                                            4 Members                     


                                            5 Guides authored

In Progress#

Introduction#

What you need#

Team#

In Progress

Introduction

What you need

Team