Difficulty
Easy
Steps
6
Time Required
10 minutes
Sections
2
- Back Panel
- 3 steps
- Wireless Card
- 3 steps
Flags
0
BackASUS Portable AiO PT2001
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Remove the grey scuff guard at the bottom of the PC by pressing down on it, and pulling it away.
- Lift the hinge and remove the grey rubber tabs on either side of the PC’s model information.
- Remove the two 7.62mm Phillips #1 screws beneath the rubber tabs under the hinge and the four 7.62mm Phillips #1 screws where the scuff guard was removed.
- Remove the two 4.74mm Phillips #1 screws under the hinge (near the hinge joints) and a 4.74mm Phillips #1 screw under the handle.
Remove the grey scuff guard at the bottom of the PC by pressing down on it, and pulling it away.
Lift the hinge and remove the grey rubber tabs on either side of the PC’s model information.
Remove the two 7.62mm Phillips #1 screws beneath the rubber tabs under the hinge and the four 7.62mm Phillips #1 screws where the scuff guard was removed.
Remove the two 4.74mm Phillips #1 screws under the hinge (near the hinge joints) and a 4.74mm Phillips #1 screw under the handle.
1024
Step 2
- Use 1-2 plastic opening tools or nylon spudgers to firmly pry open the back panel.
- We recommend that you start prying the panel where the scuff guard was removed.
- Prying the back panel will cause loud popping noises. This is just the sound of the clips that hold the back panel to the PC popping off.
- Using excess force while prying can break the clips that hold the back panel and can damage the ports on the side of the PC.
Use 1-2 plastic opening tools or nylon spudgers to firmly pry open the back panel.
We recommend that you start prying the panel where the scuff guard was removed.
Prying the back panel will cause loud popping noises. This is just the sound of the clips that hold the back panel to the PC popping off.
Using excess force while prying can break the clips that hold the back panel and can damage the ports on the side of the PC.
Step 3
- Disconnect the three cables connecting the back panel ports to the motherboard.
- Flip up the locking latch holding the two ribbon cables with a plastic opening tool and pull the cables out.
- Gently wiggle the third connector out of its socket.
Disconnect the three cables connecting the back panel ports to the motherboard.
Flip up the locking latch holding the two ribbon cables with a plastic opening tool and pull the cables out.
Gently wiggle the third connector out of its socket.
Step 4
Wireless Card
- The wireless card is on the corner of the motherboard next to the speaker. Remove the black tape to reveal the wireless card.
The wireless card is on the corner of the motherboard next to the speaker. Remove the black tape to reveal the wireless card.
Step 5
- Remove the 3.5 mm Phillips #1 screw from the wireless card.
- Remove the connectors by pulling straight up on their ends.
Remove the 3.5 mm Phillips #1 screw from the wireless card.
Remove the connectors by pulling straight up on their ends.
Step 6
- Remove the wireless card from the casing by lifting up then pulling out.
- The wireless card is fragile. Be careful when pulling it out of the casing.
Remove the wireless card from the casing by lifting up then pulling out.
The wireless card is fragile. Be careful when pulling it out of the casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Erich Fenczik Warnock
Member since: 04/17/2018
193 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
Cal Poly, Team S17-G5, Livingston Spring 2018
Member of Cal Poly, Team S17-G5, Livingston Spring 2018
CPSU-LIVINGSTON-S18S17G5
4 Members
16 Guides authored
