Asus Q504Ua Bhi5T13 Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 20 minutes

Sections

Back Panel
5 steps
Battery
4 steps
Speaker
5 steps

Flags

BackAsus Q504UA-BHI5T13
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The battery must be removed prior to the speakers. When removing the speakers, handle them as well as the wire stringing them together with care.

What you need

Step 1

              Back Panel

Ensure that the laptop is off so you do not shock yourself.

Ensure that the laptop is off so you do not shock yourself.

1024

Step 2

Use the T5 Torx screwdriver to remove the ten 1mm screws located around the back cover.

Use the T5 Torx screwdriver to remove the ten 1mm screws located around the back cover.

Step 3

Remove the two rubber pads nearest to you using the metal spudger.

Remove the two rubber pads nearest to you using the metal spudger.

Step 4

Use the Phillips #0 screwdriver to remove the two 4mm screws that are under the rubber pads.

Use the Phillips #0 screwdriver to remove the two 4mm screws that are under the rubber pads.

Step 5

Insert any of the plastic opening tools into the seam to separate the back cover (it is recommended to start at the corner of the hinges). If you did it right, then the cover should pop off.
Be careful as you may damage the tabs.

Insert any of the plastic opening tools into the seam to separate the back cover (it is recommended to start at the corner of the hinges). If you did it right, then the cover should pop off.

Be careful as you may damage the tabs.

Step 6

              Battery

Once the back cover is removed, have the laptop facing upside down with the hinges facing toward you.

Once the back cover is removed, have the laptop facing upside down with the hinges facing toward you.

Step 7

Use the Phillips #0 screwdriver to remove the five 4mm screws around the battery.

Use the Phillips #0 screwdriver to remove the five 4mm screws around the battery.

Step 8

Use the small plastic opening tool to remove the ZIF Connector on the right side of the battery.

Use the small plastic opening tool to remove the ZIF Connector on the right side of the battery.

Step 9

Remove the battery from the device.

Remove the battery from the device.

Step 10

              Speaker

We will start with the left speaker. The left speaker is the one with the letter “L” on it. Use the Phillips #0 screwdriver to remove the two 4mm screws around the left speaker.
It shares the bottom screw with the battery.
This is the screw that is shared with the battery. This screw will be removed once the battery is removed.

We will start with the left speaker. The left speaker is the one with the letter “L” on it. Use the Phillips #0 screwdriver to remove the two 4mm screws around the left speaker.

It shares the bottom screw with the battery.

This is the screw that is shared with the battery. This screw will be removed once the battery is removed.

Step 11

Use tweezers to pull the plug towards the speaker.
Take care when removing the cable. Damaging the cable will stop the part from working.

Use tweezers to pull the plug towards the speaker.

Take care when removing the cable. Damaging the cable will stop the part from working.

Step 12

Unhook the red and black twisted wire from the tabs that are between the two speakers. This prevents damage to the wires as the speakers are removed.
Remove the Left (L) speaker.

Unhook the red and black twisted wire from the tabs that are between the two speakers. This prevents damage to the wires as the speakers are removed.

Remove the Left (L) speaker.

Step 13

Now for the right speaker, use the Phillips #0 screwdriver to remove the two 4mm screws around the speaker.
It shares the bottom screw with the motherboard.
This screw is shared with the mother board, this screw will need to be removed however the mother board does not need to be removed before the speaker.

Now for the right speaker, use the Phillips #0 screwdriver to remove the two 4mm screws around the speaker.

It shares the bottom screw with the motherboard.

This screw is shared with the mother board, this screw will need to be removed however the mother board does not need to be removed before the speaker.

Step 14

Remove the Right (R) speaker from the device. Using a spudger helps to slide it out.

Remove the Right (R) speaker from the device. Using a spudger helps to slide it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    Joel Joly

Member since: 10/02/2017

129 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       USF Tampa, Team S10-G4, Thompson Fall 2017                        

                                                  Member of USF Tampa, Team S10-G4, Thompson Fall 2017 



                    USFT-THOMPSON-F17S10G4                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team