Difficulty

Moderate

Steps

12

Time Required

                          30 minutes - 1 hour

Sections

3

  • Back Panel
  • 5 steps
  • Battery
  • 4 steps
  • Touch-pad
  • 3 steps

Flags

0

  • BackAsus Q504UA-BHI5T13

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Ensure that the laptop is off so you do not shock yourself.

Ensure that the laptop is off so you do not shock yourself.

1024

Step 2

  • Use the T5 Torx screwdriver to remove the ten 1mm screws located around the back cover.

Use the T5 Torx screwdriver to remove the ten 1mm screws located around the back cover.

Step 3

  • Remove the two rubber pads nearest to you using the metal spudger.

Remove the two rubber pads nearest to you using the metal spudger.

Step 4

  • Use the Phillips #0 screwdriver to remove the two 4mm screws that are under the rubber pads.

Use the Phillips #0 screwdriver to remove the two 4mm screws that are under the rubber pads.

Step 5

  • Insert any of the plastic opening tools into the seam to separate the back cover (it is recommended to start at the corner of the hinges). If you did it right, then the cover should pop off.
  • Be careful as you may damage the tabs.

Insert any of the plastic opening tools into the seam to separate the back cover (it is recommended to start at the corner of the hinges). If you did it right, then the cover should pop off.

Be careful as you may damage the tabs.

Step 6

              Battery
  • Once the back cover is removed, have the laptop facing upside down with the hinges facing toward you.

Once the back cover is removed, have the laptop facing upside down with the hinges facing toward you.

Step 7

  • Use the Phillips #0 screwdriver to remove the five 4mm screws around the battery.

Use the Phillips #0 screwdriver to remove the five 4mm screws around the battery.

Step 8

  • Use the small plastic opening tool to remove the ZIF Connector on the right side of the battery.

Use the small plastic opening tool to remove the ZIF Connector on the right side of the battery.

Step 9

  • Remove the battery from the device.

Remove the battery from the device.

Step 10

              Touch-pad
  • Pull the large data ribbon near the touch-pad out of the way with your hands.
  • Use the Phillips #0 screwdriver to remove the three 3.0 mm screws connecting the touch-pad to the device.

Pull the large data ribbon near the touch-pad out of the way with your hands.

Use the Phillips #0 screwdriver to remove the three 3.0 mm screws connecting the touch-pad to the device.

Step 11

  • Use the small plastic opening tool to remove the ZIF Connector on the left side of the touch-pad.

Use the small plastic opening tool to remove the ZIF Connector on the left side of the touch-pad.

Step 12

  • Pry the end closest to the display up with your fingers and pull the touch-pad out.

Pry the end closest to the display up with your fingers and pull the touch-pad out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Jacob Fritsch

Member since: 11/04/2019

337 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       IUPUI, Team S1-G2, Henning Fall 2019                        

                                                  Member of IUPUI, Team S1-G2, Henning Fall 2019 



                    IUPUI-HENNING-F19S1G2                     


                                            3 Members                     


                                            3 Guides authored