Difficulty
Moderate
Steps
10
Time Required
30 minutes
Sections
3
- Battery
- 2 steps
- Asus ROG G750JH-DB71 Disassembly
- 7 steps
- RAM
- 1 step
Flags
0
BackAsus ROG G750JH-DB71
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The RAM provides memory for the Asus ROG G750JH-DB71 while running the operating system. This allows the Asus ROG G750JH-DB71 to do many tasks from taxing videogames and programs to browsing the internet. Damage to Asus ROG G750JH-DB71’s RAM could cause random crashing or a slow operating system.
To test if it’s your RAM is causing these problems you can test this using free diagnostic programs on the internet.
The Asus ROG G750JH-DB71 comes with a 12 GB DDR3-SDRAM and 24 GB of RAM in total. You can add up to 32 GB of RAM (32000 MB)
What you need
Step 1
Battery
- Ensure the laptop is powered off and unplugged before beginning.
- Flip the laptop over so the bottom case is facing up.
Ensure the laptop is powered off and unplugged before beginning.
Flip the laptop over so the bottom case is facing up.
1024
Step 2
- Push the switch near the front of the laptop to release the battery from the computer.
- Pull the battery out and away from the center of the computer.
Push the switch near the front of the laptop to release the battery from the computer.
Pull the battery out and away from the center of the computer.
Step 3
Asus ROG G750JH-DB71 Disassembly
- Use a spudger or your finger to lift up the plastic cover on back of the laptop.
- Under the plastic cover is a captive screw; unscrew it using a Phillips #00 screwdriver.
Use a spudger or your finger to lift up the plastic cover on back of the laptop.
Under the plastic cover is a captive screw; unscrew it using a Phillips #00 screwdriver.
Step 4
- Remove the cover.
- If your goal is to replace/remove only the hard drive. You don’t have to complete the following disassembly steps and can go on to the hard drive replacement guide.
Remove the cover.
If your goal is to replace/remove only the hard drive. You don’t have to complete the following disassembly steps and can go on to the hard drive replacement guide.
Step 5
- Remove the hard drive by unscrewing the 4.4 mm Phillips #00 screws.
- Remove all of the plastic caps around the edges using a pick or flathead screwdriver, and remove the screws underneath them. (one 13 mm Phillips #00, six 8 mm Phillips #00)
- Remove all of the screws underneath the cover removed previously. (six 8mm Phillips #00, three 1 mm Phillips #00)
Remove the hard drive by unscrewing the 4.4 mm Phillips #00 screws.
Remove all of the plastic caps around the edges using a pick or flathead screwdriver, and remove the screws underneath them. (one 13 mm Phillips #00, six 8 mm Phillips #00)
Remove all of the screws underneath the cover removed previously. (six 8mm Phillips #00, three 1 mm Phillips #00)
Step 6
- Push on the metal tab with a flathead screwdriver or an iFixit tool to remove the CD rom. It is located below a previously removed screw.
- Do not pull the CD rom out from the side before pushing the metal tab as it will only damage the cover.
- Remove the three (4 mm Phillips #00) screws that were previously covered by the CD rom.
Push on the metal tab with a flathead screwdriver or an iFixit tool to remove the CD rom. It is located below a previously removed screw.
Do not pull the CD rom out from the side before pushing the metal tab as it will only damage the cover.
Remove the three (4 mm Phillips #00) screws that were previously covered by the CD rom.
Step 7
- Once the screws are out and the CD rom is removed, the back cover can be taken off by hand.
- Disconnect the speaker cables located in picture 1 and 2.
- Remove two 8 mm Phillips #00 screws on each corner shown in picture 3.
Once the screws are out and the CD rom is removed, the back cover can be taken off by hand.
Disconnect the speaker cables located in picture 1 and 2.
Remove two 8 mm Phillips #00 screws on each corner shown in picture 3.
Step 8
- Pry the keyboard gently using the iFixit prying tool.
- Make sure to unhook the cables and wires from the keyboard gently in Picture 3.
Pry the keyboard gently using the iFixit prying tool.
Make sure to unhook the cables and wires from the keyboard gently in Picture 3.
Step 9
- Now you can pull the keyboard off but make sure to do so carefully without damaging or scuffing any components.
- Pull up and out at an angle as to avoid damaging the internals of the laptop.
Now you can pull the keyboard off but make sure to do so carefully without damaging or scuffing any components.
Pull up and out at an angle as to avoid damaging the internals of the laptop.
Step 10
RAM
- The RAM module is located directly in the center of the computer on top of the motherboard.
- Push in the two levers on each side of the RAM module. This frees the module from the slot and allows removal.
- Once loose, pull the RAM module away from the slot at a 45 degree angle as to not damage it.
The RAM module is located directly in the center of the computer on top of the motherboard.
Push in the two levers on each side of the RAM module. This frees the module from the slot and allows removal.
Once loose, pull the RAM module away from the slot at a 45 degree angle as to not damage it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
James Mills
Member since: 10/25/2022
471 Reputation
4 Guides authored
Badges:
6
+3 more badges
Team
UMass Dartmouth, Team 5-5, Sinclaire Fall 2022
Member of UMass Dartmouth, Team 5-5, Sinclaire Fall 2022
UMASSD-SINCLAIRE-F22S5G5
4 Members
6 Guides authored