Asus Rog G750Jm Bsi7N23 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Soundbar/speaker
6 steps
Back Plate
3 steps
Keyboard
4 steps
Motherboard
6 steps

Flags

BackAsus ROG G750JM-BSI7N23
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Soundbar/speaker

Using a plastic opening tool, remove the two rubber tabs circled in red.

Using a plastic opening tool, remove the two rubber tabs circled in red.

1024

Step 2

Remove both of the 8mm Phillips #2 screws from these slots where the rubber caps were removed.

Remove both of the 8mm Phillips #2 screws from these slots where the rubber caps were removed.

Step 3

Slide the tab to pop the battery out of its holder.
Pull the battery out of its slot.

Slide the tab to pop the battery out of its holder.

Pull the battery out of its slot.

Step 4

Remove the three 4mm Phillips #2 screws from the open battery slot as shown.
Remove the two 5mm Phillips #2 screws.

Remove the three 4mm Phillips #2 screws from the open battery slot as shown.

Remove the two 5mm Phillips #2 screws.

Step 5

Begin prying up on the plate as shown in the pictures.

Begin prying up on the plate as shown in the pictures.

Step 6

Detach the single connector using your plastic opening tool.
Remove the speaker bar.

Detach the single connector using your plastic opening tool.

Remove the speaker bar.

Step 7

              Back Plate

With the computer upside down, lift up on the rubber cap on the back plate to access the captive Phillips #2 screw.

With the computer upside down, lift up on the rubber cap on the back plate to access the captive Phillips #2 screw.

Step 8

Retract the Phillips #2 screw until the cover is loose.
The screw will not come all the way out.

Retract the Phillips #2 screw until the cover is loose.

The screw will not come all the way out.

Step 9

Pry around the edges of the plate using a plastic opening tool until the plate is removed.

Pry around the edges of the plate using a plastic opening tool until the plate is removed.

Step 10

              Keyboard

Remove the six 8mm Phillips #2 screws to remove the display.
Remove the two 4mm Phillips #2 screws.

Remove the six 8mm Phillips #2 screws to remove the display.

Remove the two 4mm Phillips #2 screws.

Step 11

Remove the four rubber tabs circled in green on the bottom of the device.
Remove the five 4mm #2 Phillips screws.
Remove the two 8mm #2 Phillips screws.
Remove the two 1cm #2 Phillips screws.

Remove the four rubber tabs circled in green on the bottom of the device.

Remove the five 4mm #2 Phillips screws.

Remove the two 8mm #2 Phillips screws.

Remove the two 1cm #2 Phillips screws.

Step 12

Pry around the keyboard on the top topside as shown to remove it from shell.

Pry around the keyboard on the top topside as shown to remove it from shell.

Step 13

Remove the four connectors using your pry tool.
The keyboard will now be separated from the main computer.

Remove the four connectors using your pry tool.

The keyboard will now be separated from the main computer.

Step 14

              Motherboard

First, remove the two 7mm #2 Phillips screws circled in red to fold the silver plate over.
Remove all the connectors shown in the orange squares. You may need to use your plastic opening tool for the smaller ones.

First, remove the two 7mm #2 Phillips screws circled in red to fold the silver plate over.

Remove all the connectors shown in the orange squares. You may need to use your plastic opening tool for the smaller ones.

Step 15

Remove the three #2 Phillips screws from the small wireless card located in the top left.

Remove the three #2 Phillips screws from the small wireless card located in the top left.

Step 16

Remove the three #2 Phillips screws from the small power button card in the top right.

Remove the three #2 Phillips screws from the small power button card in the top right.

Step 17

Remove the two #2 Phillips screws for the audio card located in the bottom right.

Remove the two #2 Phillips screws for the audio card located in the bottom right.

Step 18

Remove all 8mm #2 Phillips screws .
Remove all 2mm #2 Phillips screws.
Remove all 3mm #2 Phillips screws.
Remove all 7mm #2 Phillips screws.
Remove all 4mm #2 Phillips screws.

Remove all 8mm #2 Phillips screws .

Remove all 2mm #2 Phillips screws.

Remove all 3mm #2 Phillips screws.

Remove all 7mm #2 Phillips screws.

Remove all 4mm #2 Phillips screws.

Step 19

When all the screws are removed, pry up on the edges of the circuit board. You may need your plastic opening tool to access the edges.

When all the screws are removed, pry up on the edges of the circuit board. You may need your plastic opening tool to access the edges.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    Tanner

Member since: 09/21/2018

892 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Central Washington University, Team S1-G6, Pengilly Fall 2018                        

                                                  Member of Central Washington University, Team S1-G6, Pengilly Fall 2018 



                    CWU-PENGILLY-F18S1G6                     


                                            3 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team