Asus Rog G751Jl Bsi7T28 Sd Card Reader Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          25 - 30 minutes            

Sections

4

• Back Panel
• 2 steps
• Display Assembly
• 5 steps
• Keyboard Assembly
• 1 step
• SD Card Reader
• 2 steps

Flags

0

• BackAsus ROG G751JL-BSI7T28

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

When replacing the SD Card Reader, it is important to take care of the replacement prior to installation. This component has little receivers inside and if debris gets into this, there may be more problems down the line with the SD Card Reader. If the pins inside this are damaged, the component must be replaced so be careful.

What you need

Step 1

              Back Panel               

• With the laptop closed, turn it upside-down so the bottom is facing up toward you.

With the laptop closed, turn it upside-down so the bottom is facing up toward you.

1024

Step 2

• Place a spudger into the notch, and pry the small triangular piece away from the laptop.
• Using a Phillips #00 screwdriver, remove the single 3 mm screw.
• Place a spudger beneath the back panel and pry it away from the laptop.

Place a spudger into the notch, and pry the small triangular piece away from the laptop.

Using a Phillips #00 screwdriver, remove the single 3 mm screw.

Place a spudger beneath the back panel and pry it away from the laptop.

Step 3

              Display Assembly               

• Remove all 5mm Phillips #00 screws from the back cover.

Remove all 5mm Phillips #00 screws from the back cover.

Step 4

• Use a spudger to pry the disc drive out of the laptop.

Use a spudger to pry the disc drive out of the laptop.

Step 5

• Open the laptop and turn it so that the ASUS logo is facing you.
• Gently lift up the display hinge housing shroud, but don’t pull it completely away yet.
• Disconnect the RGB light power cable in the shroud, now the shroud can be put aside.

Open the laptop and turn it so that the ASUS logo is facing you.

Gently lift up the display hinge housing shroud, but don’t pull it completely away yet.

Disconnect the RGB light power cable in the shroud, now the shroud can be put aside.

Step 6

• Remove the 5mm Phillips #00 screws.
• Lift up the silver hinge brackets on each side of the laptop.

Remove the 5mm Phillips #00 screws.

Lift up the silver hinge brackets on each side of the laptop.

Step 7

• Remove the 5mm Phillips #00 screws from the hinges.
• Detach the ribbon cable and remove the display assembly from the laptop.

Remove the 5mm Phillips #00 screws from the hinges.

Detach the ribbon cable and remove the display assembly from the laptop.

Step 8

              Keyboard Assembly               

• Carefully lift the keyboard up, being careful to not damage the fragile ribbon connectors.
• Use an opening tool to detach the ribbon cables connecting the keyboard to the rest of the laptop.
• Remove the keyboard from the laptop.

Carefully lift the keyboard up, being careful to not damage the fragile ribbon connectors.

Use an opening tool to detach the ribbon cables connecting the keyboard to the rest of the laptop.

Remove the keyboard from the laptop.

Step 9

              SD Card Reader               

• Flip the SD card reader’s retaining arm up.
• Remove the SD card reader’s power/data ribbon cable.

Flip the SD card reader’s retaining arm up.

Remove the SD card reader’s power/data ribbon cable.

Step 10

• Remove three 3mm Phillips #0 screws from the SD card reader.
• Remove the SD card reader.

Remove three 3mm Phillips #0 screws from the SD card reader.

Remove the SD card reader.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 

                    Dylan Michael Leonard                     

Member since: 11/05/2019

423 Reputation

                                      4 Guides authored                  



                       Badges:
                       3

Team

                       UMass Dartmouth, Team S1-G1, Barthe Fall 2019                        

                                                  Member of UMass Dartmouth, Team S1-G1, Barthe Fall 2019 



                    UMASSD-BARTHE-F19S1G1                     


                                            3 Members                     


                                            4 Guides authored