Difficulty
Moderate
Steps
13
Time Required
30 minutes
Sections
1
- Fan
- 13 steps
Flags
0
BackAsus ROG G751JL-DS71
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Fan
- Lift the rubber cover found on the bottom of the laptop.
- Remove the 5.2 mm screw with a Phillips 1 Screwdriver.
Lift the rubber cover found on the bottom of the laptop.
Remove the 5.2 mm screw with a Phillips 1 Screwdriver.
1024
Step 2
- Use the standard spudger to remove the back center panel.
Use the standard spudger to remove the back center panel.
Step 3
- Use a Phillips 1 Screwdriver to remove the 5 mm screw that is located underneath the back panel.
Use a Phillips 1 Screwdriver to remove the 5 mm screw that is located underneath the back panel.
Step 4
- Pull out the optical drive found on the side of the laptop.
Pull out the optical drive found on the side of the laptop.
Step 5
- Remove the screws holding the hard drives in place using a phillips #1 screwdriver.
- Using the small flaps, remove the hard drives by hand.
Remove the screws holding the hard drives in place using a phillips #1 screwdriver.
Using the small flaps, remove the hard drives by hand.
Step 6
- Use a pair of tweezers to remove the top four rubber stoppers found on the bottom of the laptop.
Use a pair of tweezers to remove the top four rubber stoppers found on the bottom of the laptop.
Step 7
- Use a Phillips 1 Screwdriver to remove the top four 8.5 mm screws.
Use a Phillips 1 Screwdriver to remove the top four 8.5 mm screws.
Step 8
- Use a metal spudger to carefully pry the top back panel off.
- While removing the top back panel, be careful not to break the four pin connector located underneath.
- Disconnect the four-pin connector and remove the top back panel from the computer.
Use a metal spudger to carefully pry the top back panel off.
While removing the top back panel, be careful not to break the four pin connector located underneath.
Disconnect the four-pin connector and remove the top back panel from the computer.
Step 9
- Use a Phillips 1 Screwdriver to remove the four 6.8 mm screws underneath the back panel.
Use a Phillips 1 Screwdriver to remove the four 6.8 mm screws underneath the back panel.
Step 10
- Use a Phillips 1 Screwdriver to remove the ten 5.2 mm screws holding the main panel in place.
Use a Phillips 1 Screwdriver to remove the ten 5.2 mm screws holding the main panel in place.
Step 11
- Use a metal opening tool to pry the keyboard from the base of the laptop.
- Lift the keyboard carefully so as to not tear or break the four ribbon connectors underneath the keyboard.
Use a metal opening tool to pry the keyboard from the base of the laptop.
Lift the keyboard carefully so as to not tear or break the four ribbon connectors underneath the keyboard.
Step 12
- Use a pair of tweezers to undo each of the four ribbon connectors.
- The keyboard is now completely disconnected from the laptop and you can remove it.
Use a pair of tweezers to undo each of the four ribbon connectors.
The keyboard is now completely disconnected from the laptop and you can remove it.
Step 13
- Disconnect the four-pin connectors from each fan and remove them
- The fans are now completely disconnected from the laptop and you can remove them
Disconnect the four-pin connectors from each fan and remove them
The fans are now completely disconnected from the laptop and you can remove them
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Ashley Twigg
Member since: 04/01/2019
237 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
IUPUI, Team S8-G8, Wilson Spring 2019
Member of IUPUI, Team S8-G8, Wilson Spring 2019
IUPUI-WILSON-S19S8G8
4 Members
3 Guides authored
Avkash - May 31, 2019
Reply
i was wondering if i can swap the bottom case of g751jl with bottom case of g751jy? thanks a ton
