Difficulty
Moderate
Steps
11
Time Required
15 - 20 minutes
Sections
3
- CD-ROM Player
- 4 steps
- Top Rear Panel
- 3 steps
- Keyboard
- 4 steps
Flags
0
BackAsus ROG G751JL-DS71
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
CD-ROM Player
- Lift the rubber cover found on the bottom of the laptop.
- Remove the 5.2 mm screw with a Phillips 1 Screwdriver.
Lift the rubber cover found on the bottom of the laptop.
Remove the 5.2 mm screw with a Phillips 1 Screwdriver.
1024
Step 2
- Use the nylon spudger to remove the back center panel.
Use the nylon spudger to remove the back center panel.
Step 3
- Use a Phillips 1 Screwdriver to remove the 5 mm screw that is located underneath the back panel.
Use a Phillips 1 Screwdriver to remove the 5 mm screw that is located underneath the back panel.
Step 4
- Pull out the optical drive found on the side of the laptop.
Pull out the optical drive found on the side of the laptop.
Step 5
Top Rear Panel
- Use a pair of tweezers to remove the top four rubber stoppers found on the bottom of the laptop.
Use a pair of tweezers to remove the top four rubber stoppers found on the bottom of the laptop.
Step 6
- Use a Phillips 1 Screwdriver to remove the top four 8.5 mm screws.
Use a Phillips 1 Screwdriver to remove the top four 8.5 mm screws.
Step 7
- Use a nylon spudger to carefully pry the top back panel off.
- While removing the top back panel, be careful not to break the four pin connector located underneath.
- Disconnect the four-pin connector and remove the top back panel from the computer.
Use a nylon spudger to carefully pry the top back panel off.
While removing the top back panel, be careful not to break the four pin connector located underneath.
Disconnect the four-pin connector and remove the top back panel from the computer.
Step 8
Keyboard
- Use a Phillips 1 Screwdriver to remove the four 6.8 mm screws underneath the back panel.
- Lift away the metal housings from each side of the laptop.
Use a Phillips 1 Screwdriver to remove the four 6.8 mm screws underneath the back panel.
Lift away the metal housings from each side of the laptop.
Step 9
- Use a Phillips 1 Screwdriver to remove the ten 5.2 mm screws holding the main panel in place.
- Use a Phillips 1 Screwdriver to remove the four 5.2 mm screws underneath the center panel.
Use a Phillips 1 Screwdriver to remove the ten 5.2 mm screws holding the main panel in place.
Use a Phillips 1 Screwdriver to remove the four 5.2 mm screws underneath the center panel.
Step 10
- Use a plastic opening tool to pry the keyboard from the base of the laptop.
- Lift the keyboard carefully so as to not tear or break the four ribbon connectors underneath the keyboard.
Use a plastic opening tool to pry the keyboard from the base of the laptop.
Lift the keyboard carefully so as to not tear or break the four ribbon connectors underneath the keyboard.
Step 11
- Use a pair of tweezers to undo each of the four ribbon connectors.
- The keyboard is now completely disconnected from the laptop and you can remove it.
Use a pair of tweezers to undo each of the four ribbon connectors.
The keyboard is now completely disconnected from the laptop and you can remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Aurora Rios
Member since: 01/22/2018
890 Reputation
4 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S16-G1, Banghart Winter 2018
Member of Cal Poly, Team S16-G1, Banghart Winter 2018
CPSU-BANGHART-W18S16G1
4 Members
22 Guides authored
Michael Chiu - Oct 24, 2022
Reply
Only shows you how to remove keyboard panel from chasis, not how to actually remove the keyborad from the keyboard panel to replace. sad.
