Difficulty

Difficult

Steps

22

Time Required

                          2 hours

Sections

2

  • Battery
  • 15 steps
  • Fan
  • 7 steps

Flags

0

  • BackAsus ROG G752V

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Look at our Asus Rog G752V Troubleshooting page to identify the symptoms of a dirty or old fan. If your symptoms match, follow this guide to clean or replace your fan.

Before you start working, make sure that your Asus ROG G752V laptop charger is disconnected, and your laptop is turned off. In addition, follow the warnings that are attached to images in this guide.

What you need

Step 1

              Battery
  • Make sure you disconnect the charger before starting this guide.
  • Pick out all 11 rubber plugs off of the back cover with a pair of tweezers.

Make sure you disconnect the charger before starting this guide.

Pick out all 11 rubber plugs off of the back cover with a pair of tweezers.

1024

Step 2

  • Using the Phillips #0 screwdriver, unscrew all twelve 5.2 mm screws on the back of the laptop.
  • There is one 5.2 mm screw under the rubber plug in the middle.

Using the Phillips #0 screwdriver, unscrew all twelve 5.2 mm screws on the back of the laptop.

There is one 5.2 mm screw under the rubber plug in the middle.

Step 3

  • Pull up the rubber seal and the service cover will come off.

Pull up the rubber seal and the service cover will come off.

Step 4

  • Using the Phillips #00 screwdriver, remove the six 5.2 mm screws under the service cover.

Using the Phillips #00 screwdriver, remove the six 5.2 mm screws under the service cover.

Step 5

  • Using your hands, pull the optical drive out.

Using your hands, pull the optical drive out.

Step 6

  • Use the iFixit Opening Tool to pry apart the back panel from the main body of the laptop.
  • Start from the front side of the laptop and then continue to the side for easier access.

Use the iFixit Opening Tool to pry apart the back panel from the main body of the laptop.

Start from the front side of the laptop and then continue to the side for easier access.

Step 7

  • Remove the hinge on the back of the laptop cover using the iFixit Opening Tool. The piece should pop off.
  • Be gentle with the cover because there is a speaker wire attached to it.

Remove the hinge on the back of the laptop cover using the iFixit Opening Tool. The piece should pop off.

Be gentle with the cover because there is a speaker wire attached to it.

Step 8

  • Disconnect the speaker wire.

Disconnect the speaker wire.

Step 9

  • Slowly pull out the keyboard while lifting it about an inch.
  • There are cables attached to the keyboard and motherboard. DO NOT lift it more than 2 inches above the laptop.

Slowly pull out the keyboard while lifting it about an inch.

There are cables attached to the keyboard and motherboard. DO NOT lift it more than 2 inches above the laptop.

Step 10

  • Using an ESD safe tool, detach all 3 ribbon cables securing the keyboard to the laptop.
  • To unlock a ZIF connector, use the tip of a spudger or your fingernail to flip up the small, hinged locking flap.

Using an ESD safe tool, detach all 3 ribbon cables securing the keyboard to the laptop.

To unlock a ZIF connector, use the tip of a spudger or your fingernail to flip up the small, hinged locking flap.

Step 11

  • Once the cables are detached, lift the keyboard about 2 inches up and remove it from the rest of the body.
  • Make sure that the screen is open like the photo. This will ensure that none your laptop components will not be bent.

Once the cables are detached, lift the keyboard about 2 inches up and remove it from the rest of the body.

Make sure that the screen is open like the photo. This will ensure that none your laptop components will not be bent.

Step 12

  • Disconnect the battery cable from its motherboard socket by gently pulling it towards the left of the socket.
  • Pull parallel to the motherboard, not straight up.

Disconnect the battery cable from its motherboard socket by gently pulling it towards the left of the socket.

Pull parallel to the motherboard, not straight up.

Step 13

  • Remove two 5.8 mm screws holding the screen and the laptop located at the hinge.
  • This will unlatch the screen from the laptop entirely.
  • Remove the screen.

Remove two 5.8 mm screws holding the screen and the laptop located at the hinge.

This will unlatch the screen from the laptop entirely.

Remove the screen.

Step 14

  • Remove the four 5.8 mm screws securing the battery to the laptop.

Remove the four 5.8 mm screws securing the battery to the laptop.

Step 15

  • Use your hands to remove the battery.
  • If you’re having trouble, push down on the black plastic on the screen side of the battery. This should release the battery.

Use your hands to remove the battery.

If you’re having trouble, push down on the black plastic on the screen side of the battery. This should release the battery.

Step 16

              Fan
  • Unplug the fan-motherboard connection cable.

Unplug the fan-motherboard connection cable.

Step 17

  • Unscrew and remove the three 5.8mm screws on the small circuit board to the right of the right side fan with a Phillips #00 screwdriver.
  • Lift up the small circuit board covering the fan and put it aside.

Unscrew and remove the three 5.8mm screws on the small circuit board to the right of the right side fan with a Phillips #00 screwdriver.

Lift up the small circuit board covering the fan and put it aside.

Step 18

  • Using a Phillips #00 screwdriver, remove the three 5.2 mm screws that connect the fan to the motherboard.

Using a Phillips #00 screwdriver, remove the three 5.2 mm screws that connect the fan to the motherboard.

Step 19

  • With your hands, slowly and carefully lift up the right side fan.

With your hands, slowly and carefully lift up the right side fan.

Step 20

  • Carefully unlatch the left side fan cable from the motherboard.

Carefully unlatch the left side fan cable from the motherboard.

Step 21

  • Using a Phillips #00 screwdriver, remove the two 5.8mm screws that connect the left fan to the motherboard.

Using a Phillips #00 screwdriver, remove the two 5.8mm screws that connect the left fan to the motherboard.

Step 22

  • With your hands, carefully lift the left fan and unlatch the fan from the motherboard.

With your hands, carefully lift the left fan and unlatch the fan from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 6 other contributors 


                    Jeong

Member since: 09/16/2019

1,055 Reputation

                                      5 Guides authored                  



                       Badges:
                       12





                                                        +9 more badges

Team

                       Embry-Riddle Aeronautical University, Team S2-G36, Watkins Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S2-G36, Watkins Fall 2019 



                    ERAU-WATKINS-F19S2G36                     


                                            4 Members                     


                                            6 Guides authored

Citizen Gone - Jul 24, 2022

Reply

Awesome! Epic guide thank you!