Asus Rog G75Vx Bhi7N11 Speakers Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

ASUS ROG G75VX-BHI7N11 Disassembly
8 steps
Speakers
2 steps

Flags

BackASUS ROG G75VX-BHI7N11
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              ASUS ROG G75VX-BHI7N11 Disassembly

Remove the 6 screws on the edge of the laptop using a screwdriver.
Remove the back casing being held on by the one single screw. First, lift the casing at the edge where the screw once was, then carefully lift at the rest of the edges to loosen the casing. Pull the casing towards the edge where the screw was.
Remove the battery by sliding the switch circled in the picture and pulling the battery out.

Remove the 6 screws on the edge of the laptop using a screwdriver.

Remove the back casing being held on by the one single screw. First, lift the casing at the edge where the screw once was, then carefully lift at the rest of the edges to loosen the casing. Pull the casing towards the edge where the screw was.

Remove the battery by sliding the switch circled in the picture and pulling the battery out.

1024

Step 2

Remove the 11 screws circled in the picture using a Phillips head screwdriver. They should be labeled on the laptop with a capital A, shown circled in red.
Remove the screw labeled C.

Remove the 11 screws circled in the picture using a Phillips head screwdriver. They should be labeled on the laptop with a capital A, shown circled in red.

Remove the screw labeled C.

Step 3

Remove the 5 screws circled in the picture, located where the battery pack once was.

Remove the 5 screws circled in the picture, located where the battery pack once was.

Step 4

Remove the DVD ROM on the side of the computer, by pulling it out. If necessary, use a plastic opening tool.

Remove the DVD ROM on the side of the computer, by pulling it out. If necessary, use a plastic opening tool.

Step 5

Remove the three screws located where the DVD ROM once was, on the screen side of the laptop.

Remove the three screws located where the DVD ROM once was, on the screen side of the laptop.

Step 6

Flip the laptop over and pop the back cover off behind the screen, by grabbing it on either side and pulling it up, vertically off of the laptop.
There is a cable connecting the cover to the laptop, shown in picture 2.
Disconnect the cable by pulling apart the white connectors, shown in picture 3.

Flip the laptop over and pop the back cover off behind the screen, by grabbing it on either side and pulling it up, vertically off of the laptop.

There is a cable connecting the cover to the laptop, shown in picture 2.

Disconnect the cable by pulling apart the white connectors, shown in picture 3.

Step 7

There will be two smaller and two larger black screws on each hinge holding the laptop screen onto the computer. Remove all four of the larger screws with your P0 screwdriver.
There is one screw on either side of the keyboards, next to the screen hinges. Remove both screws.

There will be two smaller and two larger black screws on each hinge holding the laptop screen onto the computer. Remove all four of the larger screws with your P0 screwdriver.

There is one screw on either side of the keyboards, next to the screen hinges. Remove both screws.

Step 8

You may now remove the keyboard plate. Simply lift from the back, and pull it off all the way around.
Caution with removing the keyboard, as there are 5 ribbon cables that connect the motherboard to the keyboard (motherboard port locations shown in picture 2).
The ribbon cables must be carefully disconnected from the motherboard side, by flipping a latch on the port and pulling the ribbon out.

You may now remove the keyboard plate. Simply lift from the back, and pull it off all the way around.

Caution with removing the keyboard, as there are 5 ribbon cables that connect the motherboard to the keyboard (motherboard port locations shown in picture 2).

The ribbon cables must be carefully disconnected from the motherboard side, by flipping a latch on the port and pulling the ribbon out.

Step 9

              Speakers

Locate the black speakers located in the bottom corner of the laptop near the foil.
Remove the four screws holding the speakers in.

Locate the black speakers located in the bottom corner of the laptop near the foil.

Remove the four screws holding the speakers in.

Step 10

Locate the black and white cable connected to the speaker, and slide it toward you, out of its port.
Lift up a small portion of the foil tape, and remove the cable from underneath.
Your speaker is now removed, and ready to be replaced.

Locate the black and white cable connected to the speaker, and slide it toward you, out of its port.

Lift up a small portion of the foil tape, and remove the cable from underneath.

Your speaker is now removed, and ready to be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 4 other contributors

                    Logan Smith

Member since: 01/25/2017

783 Reputation

                                      4 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team 8-3, Banghart Winter 2017                        

                                                  Member of Cal Poly, Team 8-3, Banghart Winter 2017 



                    CPSU-BANGHART-W17S8G3                     


                                            4 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team