Difficulty

Moderate

Steps

18

Time Required

                          25 minutes

Sections

5

  • Back Panel
  • 2 steps
  • Battery
  • 2 steps
  • Hard Drive
  • 2 steps
  • Fan
  • 5 steps
  • Motherboard
  • 7 steps

Flags

0

  • BackAsus ROG Strix GL702VM-BHI7N09

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Flip the laptop over to the back panel, with the serial numbers facing up.
  • Using a Phillips #1 screwdriver, remove the ten 12 mm screws from the back panel.

Flip the laptop over to the back panel, with the serial numbers facing up.

Using a Phillips #1 screwdriver, remove the ten 12 mm screws from the back panel.

1024

Step 2

  • The snap seals don’t need a lot of pressure to open, and may break if forced. Be gentle with the opening tool.
  • Wedge the sharp edge of the plastic opening tool into the seam between the back panel and the rest of the laptop, then gently pry the panel up.
  • There will be a snapping sound as you remove the back panel, but that is just the seal loosening.
  • Continue breaking the seals by sliding the plastic opening tool around the entire laptop under the seam until the back panel is free.
  • Once you have broken all the seals, carefully lift the panel off.

The snap seals don’t need a lot of pressure to open, and may break if forced. Be gentle with the opening tool.

Wedge the sharp edge of the plastic opening tool into the seam between the back panel and the rest of the laptop, then gently pry the panel up.

There will be a snapping sound as you remove the back panel, but that is just the seal loosening.

Continue breaking the seals by sliding the plastic opening tool around the entire laptop under the seam until the back panel is free.

Once you have broken all the seals, carefully lift the panel off.

Step 3

              Battery
  • Unplug the battery from the motherboard.

Unplug the battery from the motherboard.

Step 4

  • Unscrew the 3.8 mm Phillips #1 screw on the top right hand corner of the battery.
  • Lift battery from laptop frame.

Unscrew the 3.8 mm Phillips #1 screw on the top right hand corner of the battery.

Lift battery from laptop frame.

Step 5

              Hard Drive
  • Using a Phillips #1 screwdriver, remove the four 4 mm screws holding the hard drive.

Using a Phillips #1 screwdriver, remove the four 4 mm screws holding the hard drive.

Step 6

  • Pull the hard drive directly away from the fan just above it.
  • The connecting pins should slide out easily, but you might have to move the hard drive around a bit to loosen the pins.

Pull the hard drive directly away from the fan just above it.

The connecting pins should slide out easily, but you might have to move the hard drive around a bit to loosen the pins.

Step 7

              Fan
  • Using a Phillips #1 screwdriver, remove the four indicated 4 mm screws that hold the black fan and the silver one adjacent to it.

Using a Phillips #1 screwdriver, remove the four indicated 4 mm screws that hold the black fan and the silver one adjacent to it.

Step 8

  • The smaller black fan must be removed before the larger gray fan on the right can be taken out.
  • To remove the black fan, pull gently on the connecting cables outlined.

The smaller black fan must be removed before the larger gray fan on the right can be taken out.

To remove the black fan, pull gently on the connecting cables outlined.

Step 9

  • Unplug the white connector by gently pulling the cables.
  • Lift off the gray fan.

Unplug the white connector by gently pulling the cables.

Lift off the gray fan.

Step 10

  • Using a Phillips #1 screwdriver, remove the two indicated 4 mm screws from the other gray fan.

Using a Phillips #1 screwdriver, remove the two indicated 4 mm screws from the other gray fan.

Step 11

  • Unplug the white connector by gently pulling it towards the center of the computer.
  • Lift the fan out of the body of the laptop to remove it.

Unplug the white connector by gently pulling it towards the center of the computer.

Lift the fan out of the body of the laptop to remove it.

Step 12

              Motherboard
  • Disconnect the speakers connectors located in each of the bottom corners.
  • Gently pull the wire up from the motherboard.
  • Once the wire is disconnected, pull the speaker out.

Disconnect the speakers connectors located in each of the bottom corners.

Gently pull the wire up from the motherboard.

Once the wire is disconnected, pull the speaker out.

Step 13

  • Gently lift the graphics card from the motherboard.

Gently lift the graphics card from the motherboard.

Step 14

  • Use reverse pliers to detach ribbon connectors from the motherboard.

Use reverse pliers to detach ribbon connectors from the motherboard.

Step 15

  • Remove each of the 4.7 mm Phillips #1 screws marked by a white arrow on the motherboard.
  • Remove the 6.7 mm Phillips #1 screws from the metal latches on the hinge-side corners.
  • The 4.7 mm Phillips #1 screw on the far left of the motherboard is covered by the black connecting wire in Step 5.

Remove each of the 4.7 mm Phillips #1 screws marked by a white arrow on the motherboard.

Remove the 6.7 mm Phillips #1 screws from the metal latches on the hinge-side corners.

The 4.7 mm Phillips #1 screw on the far left of the motherboard is covered by the black connecting wire in Step 5.

Step 16

  • Gently pull on black connecting wire to disconnect the monitor screen from the motherboard.
  • This will uncover the far left 4.7 mm Phillips #1 screw.

Gently pull on black connecting wire to disconnect the monitor screen from the motherboard.

This will uncover the far left 4.7 mm Phillips #1 screw.

Step 17

  • Lift the metal latches on both sides.
  • This can be easily done by opening the laptop after the metal latch screws have been removed.

Lift the metal latches on both sides.

This can be easily done by opening the laptop after the metal latch screws have been removed.

Step 18

  • Remove the motherboard from the laptop frame.
  • You will need to pull the motherboard to the side as well as lifting it to free its various ports from the sides of the laptop case.
  • There is adhesive attaching the final ribbon connector to the bottom of the motherboard. This will need to be removed.

Remove the motherboard from the laptop frame.

You will need to pull the motherboard to the side as well as lifting it to free its various ports from the sides of the laptop case.

There is adhesive attaching the final ribbon connector to the bottom of the motherboard. This will need to be removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors 


                    Gunnar Hudson

Member since: 11/04/2019

248 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Idaho State University, Team S1-G5, Watkins Fall 2019                        

                                                  Member of Idaho State University, Team S1-G5, Watkins Fall 2019 



                    ISU-WATKINS-F19S1G5                     


                                            4 Members                     


                                            2 Guides authored

Hank Muller - Jan 20, 2020

Reply

OK but where can I actually buy the replacement motherboard?