Difficulty

Moderate

Steps

7

Time Required

                          20 - 25 minutes

Sections

3

  • Back Case
  • 2 steps
  • Battery
  • 4 steps
  • Trackpad
  • 1 step

Flags

4

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackASUS Transformer Book Flip TP500LA

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Case
  • Remove the ten 10 mm Phillips #0 screws found on the computer’s back case.

Remove the ten 10 mm Phillips #0 screws found on the computer’s back case.

1024

Step 2

  • Slide a heavy-duty spudger between the back case and the computer.
  • Slowly work around the edges to undo the clips to fully separate the back case from the computer.
  • Gently lift off the back case.

Slide a heavy-duty spudger between the back case and the computer.

Slowly work around the edges to undo the clips to fully separate the back case from the computer.

Gently lift off the back case.

Step 3

              Battery
  • Slide a heavy-duty spudger into the ZIF connector and gently flip up the retaining flap to open the connector.
  • Pull the blue tab to remove the ribbon.

Slide a heavy-duty spudger into the ZIF connector and gently flip up the retaining flap to open the connector.

Pull the blue tab to remove the ribbon.

Step 4

  • Remove the three 5 mm Phillips #0 screws.
  • Remove the single 6 mm Phillips #0 screw.

Remove the three 5 mm Phillips #0 screws.

Remove the single 6 mm Phillips #0 screw.

Step 5

  • Use the heavy-duty spudger to pry the white 8-pin connector away from the motherboard.
  • Gently pull the connector away from the motherboard.
  • The black 8-pin connector on the motherboard is very fragile, so be careful when removing the white 8-pin connector.

Use the heavy-duty spudger to pry the white 8-pin connector away from the motherboard.

Gently pull the connector away from the motherboard.

The black 8-pin connector on the motherboard is very fragile, so be careful when removing the white 8-pin connector.

Step 6

  • Use the blue plastic opening tool to loosen and remove the three black wires from the battery.
  • Slide the battery out from the computer to remove.

Use the blue plastic opening tool to loosen and remove the three black wires from the battery.

Slide the battery out from the computer to remove.

Step 7

              Trackpad
  • The trackpad is nestled into a small cutout on the opposite side as the fan.
  • Remove the trackpad from the device.

The trackpad is nestled into a small cutout on the opposite side as the fan.

Remove the trackpad from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Graham Haigood

Member since: 02/23/2021

253 Reputation

                                      3 Guides authored                  



                       Badges:
                       3

Team

                       The Citadel Military College of South Carolina, Team S3-G3, Eggleston Spring 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team S3-G3, Eggleston Spring 2021 



                    CMCSC-EGGLESTON-S21S3G3                     


                                            3 Members                     


                                            3 Guides authored