Difficulty
Moderate
Steps
8
Time Required
Suggest a time??
Sections
1
- Motherboard
- 8 steps
Flags
2
Better Introduction
Improve this guide by completing or revising its introduction.
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackASUS TUF Gaming FX505DY
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Motherboard
- With a Phillips 0-bit screwdriver, remove six 13.5 mm screws located on the edge of the panel.
- With a Phillips 0-bit screwdriver, remove five 6.4 mm screws located on the edge and center of the panel.
With a Phillips 0-bit screwdriver, remove six 13.5 mm screws located on the edge of the panel.
With a Phillips 0-bit screwdriver, remove five 6.4 mm screws located on the edge and center of the panel.
1024
Step 2
- With a Phillips 0-bit screwdriver, remove eight 5.0 mm screws on the silver brackets
- With a Phillips 0-bit screwdriver, remove two 5.0 mm screws holding the edge of the fans in place
With a Phillips 0-bit screwdriver, remove eight 5.0 mm screws on the silver brackets
With a Phillips 0-bit screwdriver, remove two 5.0 mm screws holding the edge of the fans in place
Step 3
- Gently remove all power cables connecting the fans to the motherboard.
- Once all cables and screws are removed, carefully lift up and remove the fans and heat sink
Gently remove all power cables connecting the fans to the motherboard.
Once all cables and screws are removed, carefully lift up and remove the fans and heat sink
Step 4
- With a Phillips 0-bit screwdriver, unscrew four 5.0 mm screws.
- Disconnect the primary connector cable located at the bottom left and carefully remove the module.
With a Phillips 0-bit screwdriver, unscrew four 5.0 mm screws.
Disconnect the primary connector cable located at the bottom left and carefully remove the module.
Step 5
- With a Phillips 0-bit screwdriver, unscrew four 5.0 mm top screws holding the hard drive in place.
- Pinch the top left corner with your finger and slide the harddrive out of its casing.
With a Phillips 0-bit screwdriver, unscrew four 5.0 mm top screws holding the hard drive in place.
Pinch the top left corner with your finger and slide the harddrive out of its casing.
Step 6
- With a Phillips 0-bit screwdriver, unscrew two 5.0 mm screws holding SSD down to the motherboard on the right side of the board
- Slide module out of protective casing to remove piece.
With a Phillips 0-bit screwdriver, unscrew two 5.0 mm screws holding SSD down to the motherboard on the right side of the board
Slide module out of protective casing to remove piece.
Step 7
- On the center of the motherboard, lightly push down on the metal clamps holding down the RAM module.
- Once unclipped, carefully remove the module and secure in a safe place.
On the center of the motherboard, lightly push down on the metal clamps holding down the RAM module.
Once unclipped, carefully remove the module and secure in a safe place.
Step 8
- With a size 0 Phillips screwdriver, unscrew three center 5 mm screws securing the board in place.
- Carefully lift the board and place in a safe area.
With a size 0 Phillips screwdriver, unscrew three center 5 mm screws securing the board in place.
Carefully lift the board and place in a safe area.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Sebastian Frederick Klincewicz
Member since: 10/04/2022
325 Reputation
3 Guides authored
Badges:
4
+1 more badge
Team
The Citadel Military College of South Carolina, Team 3-19, Eggleston Fall 2022
Member of The Citadel Military College of South Carolina, Team 3-19, Eggleston Fall 2022
CMCSC-EGGLESTON-F22S3G19
2 Members
3 Guides authored
