Asus U46E Ral7 Back Panel Removal Guide Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

ASUS U46E-RAL7 Back Panel Removal Guide
9 steps

Flags

BackASUS U46E-RAL7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              ASUS U46E-RAL7 Back Panel Removal Guide

Remove two (2) 9mm x 4mm screws from the back panel with the size 0 Phillips head screwdriver.
Remove two (2) 7mm x 4mm screws from the back panel with the size 0 Phillips head screwdriver.
Remove six (6) 7mm x 4mm screws with the size 0 Phillips head screwdriver.
Remove three (3) 3mm x 3mm screws with the size 0 Phillips head screwdriver.
Remove one (1) 4mm x 4mm screws with the size 0 Phillips head screwdriver.

Remove two (2) 9mm x 4mm screws from the back panel with the size 0 Phillips head screwdriver.

Remove two (2) 7mm x 4mm screws from the back panel with the size 0 Phillips head screwdriver.

Remove six (6) 7mm x 4mm screws with the size 0 Phillips head screwdriver.

Remove three (3) 3mm x 3mm screws with the size 0 Phillips head screwdriver.

Remove one (1) 4mm x 4mm screws with the size 0 Phillips head screwdriver.

1024

Step 2

Remove the rubber caps (4) with the tweezers. If the rubber caps are not removed easily, pull gently. The caps are glued down.
Remove four (4) 7mm x 4mm screws with the size 0 Phillips head screwdriver.

Remove the rubber caps (4) with the tweezers. If the rubber caps are not removed easily, pull gently. The caps are glued down.

Remove four (4) 7mm x 4mm screws with the size 0 Phillips head screwdriver.

Step 3

Remove the L shaped panel with the plastic opening tool by inserting it into the indent along the USB port side of the laptop.
Push down gently on the plastic opening tool until part of the panel pops up.
Use your fingers to pop the panel off.

Remove the L shaped panel with the plastic opening tool by inserting it into the indent along the USB port side of the laptop.

Push down gently on the plastic opening tool until part of the panel pops up.

Use your fingers to pop the panel off.

Step 4

Remove three (3) 5mm x 4mm screws with the size 0 Phillips head screwdriver.
Remove one (1) 4mm x 4mm (closest to the battery) screw with the size 0 Phillips head screwdriver.

Remove three (3) 5mm x 4mm screws with the size 0 Phillips head screwdriver.

Remove one (1) 4mm x 4mm (closest to the battery) screw with the size 0 Phillips head screwdriver.

Step 5

Remove the CD ROM drive by inserting the plastic opening tool between the drive and the laptop’s side.
Push down gently to eject the drive.
Pull the drive straight out to remove the part from the laptop.

Remove the CD ROM drive by inserting the plastic opening tool between the drive and the laptop’s side.

Push down gently to eject the drive.

Pull the drive straight out to remove the part from the laptop.

Step 6

Remove three (3) 3mm x 3mm screws with the size 0 Phillips head screwdriver.

Step 7

Flip the device so that the laptop will open away from you to remove the hinge cover behind the screen.
Place index fingers underneath the hinge cover and gently pull up.
The cover will pop off easily with a click.
Remove five (5) 5mm x 4mm screws from the hinge compartments of the device with the size 0 phillips head screwdriver.

Flip the device so that the laptop will open away from you to remove the hinge cover behind the screen.

Place index fingers underneath the hinge cover and gently pull up.

The cover will pop off easily with a click.

Remove five (5) 5mm x 4mm screws from the hinge compartments of the device with the size 0 phillips head screwdriver.

Step 8

Open the screen.
Carefully lift the keyboard panel. The keyboard will be attached to the motherboard by two ribbons.
To disconnect the ribbons, use your fingernails to push down gently on the protruding plastic at the base of the connector. There is a soft click and ribbon releases. Repeat for the other ribbon.

Open the screen.

Carefully lift the keyboard panel. The keyboard will be attached to the motherboard by two ribbons.

To disconnect the ribbons, use your fingernails to push down gently on the protruding plastic at the base of the connector. There is a soft click and ribbon releases. Repeat for the other ribbon.

Step 9

Remove the keyboard from the computer to reveal the motherboard.

Remove the keyboard from the computer to reveal the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Vanessa Ng

Member since: 01/19/2017

419 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Eastern Washington University, Team 1-1, Mathisen Winter 2017                        

                                                  Member of Eastern Washington University, Team 1-1, Mathisen Winter 2017 



                    EWU-MATHISEN-W17S1G1                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team