Difficulty
Moderate
Steps
8
Time Required
6 minutes
Sections
2
- Keyboard
- 4 steps
- LCD Screen
- 4 steps
Flags
0
BackAsus U47VC-DS51
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Keyboard
- Remove 9 screws from bottom of notebook using PH00 bit + 1 under hard drive bay.
- Remove 3 screws from bottom of notebook using PH00 bit. 1 is same screw spec as the other 9, and 2 are shorter.
Remove 9 screws from bottom of notebook using PH00 bit + 1 under hard drive bay.
Remove 3 screws from bottom of notebook using PH00 bit. 1 is same screw spec as the other 9, and 2 are shorter.
1024
Step 2
- Using the black spudger, insert its flat end between the crevice where the color changes from grey to black.
- The keyboard is very tightly secured.
- Carefully ease the spudger’s end along the crevice, going around the entire frame.
- The back connectors are short, so be careful when lifting.
Using the black spudger, insert its flat end between the crevice where the color changes from grey to black.
The keyboard is very tightly secured.
Carefully ease the spudger’s end along the crevice, going around the entire frame.
The back connectors are short, so be careful when lifting.
Step 3
- Lift the keyboard from the front where it is closest to the screen.
- Disconnect the large and small ZIF connectors attached to the motherboard by flipping the light-colored part of the switch.
Lift the keyboard from the front where it is closest to the screen.
Disconnect the large and small ZIF connectors attached to the motherboard by flipping the light-colored part of the switch.
Step 4
- Remove the third and last ZIF connector on the motherboard by flipping up the dark-colored part of the switch.
- Now, the component should come completely free.
Remove the third and last ZIF connector on the motherboard by flipping up the dark-colored part of the switch.
Now, the component should come completely free.
Step 5
LCD Screen
- Unscrew the two 4mm phillips head #00 screws.
Unscrew the two 4mm phillips head #00 screws.
Step 6
- Use the black spudger to pry the face plate off.
- The face plate is attached with adhesive.
- Gently peel the face plate from the base.
Use the black spudger to pry the face plate off.
The face plate is attached with adhesive.
Gently peel the face plate from the base.
Step 7
- Unscrew the four 3mm Phillips head #00 screws holding the screen to the base.
- When sitting upright, the screen should fall forward from the top.
Unscrew the four 3mm Phillips head #00 screws holding the screen to the base.
When sitting upright, the screen should fall forward from the top.
Step 8
- Unease the yellow connecting tape with the spudger at the bottom of the screen.
- Pull the connector straight down and it will disconnect fairly easy.
- The screen should then be free to be removed.
Unease the yellow connecting tape with the spudger at the bottom of the screen.
Pull the connector straight down and it will disconnect fairly easy.
The screen should then be free to be removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Brady Roberson
Member since: 01/18/2017
211 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
South Arkansas Community College, Team 1-1, Mitchell Spring 2017
Member of South Arkansas Community College, Team 1-1, Mitchell Spring 2017
SACC-MITCHELL-S17S1G1
5 Members
5 Guides authored
