Asus U50F Rbbag05 Ports Usb Audio Jack Microphone Jack E Sata Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Battery
2 steps
Underpanel
3 steps
Hard Drive
3 steps
Optical Drive
3 steps
Keyboard
3 steps
Random Access Memory (RAM)
2 steps
Upper Case
4 steps
Ports (USB/Audio Jack/Microphone Jack/E-SATA)
3 steps

Flags

BackAsus U50F-RBBAG05
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

BE CAREFUL when conducting this repair, as there are many loose screws that can easily be lost. Also, there are many bundles of wires which can easily be damaged if they are forcefully and carelessly removed. Lastly, make sure all your components are safely set down and not dropped, as this can cause long term damage.

What you need

Step 1

              Battery

Turn the laptop over so the bottom is facing up.
Slide the two tabs on the bottom of the laptop toward the edges of laptop.
Slide the left tab to the left to lock it into the unlocked position. The red showing next to the tab signifies that it’s unlocked.
You will have to hold the right tab to the right to keep the slot unlocked while removing the battery.

Turn the laptop over so the bottom is facing up.

Slide the two tabs on the bottom of the laptop toward the edges of laptop.

Slide the left tab to the left to lock it into the unlocked position. The red showing next to the tab signifies that it’s unlocked.

You will have to hold the right tab to the right to keep the slot unlocked while removing the battery.

1024

Step 2

Hold down the tab on the right side, then begin sliding the battery out.
Remove the old battery.
Next, insert the new battery into the empty slot. Release the right tab to begin locking the new battery into place. Slide the left tab to the right to completely lock the battery into the slot. The red that was showing near the left tab should be gone. This signifies that the battery is locked into place.

Hold down the tab on the right side, then begin sliding the battery out.

Remove the old battery.

Next, insert the new battery into the empty slot. Release the right tab to begin locking the new battery into place. Slide the left tab to the right to completely lock the battery into the slot. The red that was showing near the left tab should be gone. This signifies that the battery is locked into place.

Step 3

              Underpanel

Remove the six screws using a Phillips #1 screwdriver.

Remove the six screws using a Phillips #1 screwdriver.

Step 4

Pry the lower panel up with your fingernail or a spudger.

Pry the lower panel up with your fingernail or a spudger.

Step 5

Lift up on the panel and remove it.

Lift up on the panel and remove it.

Step 6

              Hard Drive

Remove the two screws using a Phillips #1 screwdriver.

Remove the two screws using a Phillips #1 screwdriver.

Step 7

Using your finger, push the hard drive back.
Pry up the drive with an opening tool (or your fingernail).

Using your finger, push the hard drive back.

Pry up the drive with an opening tool (or your fingernail).

Step 8

Pull back on the hard drive and lift upwards.
Remove the component completely.

Pull back on the hard drive and lift upwards.

Remove the component completely.

Step 9

              Optical Drive

Remove the single screw.

Remove the single screw.

Step 10

Use the plastic opening tool to push the drive out from the back.

Use the plastic opening tool to push the drive out from the back.

Step 11

Pull the drive out and remove completely.
When reassembling the drive, lay the laptop with the base towards the floor. Then, push the drive all the way in. Otherwise, the drive will become stuck and be difficult to reassemble.

Pull the drive out and remove completely.

When reassembling the drive, lay the laptop with the base towards the floor. Then, push the drive all the way in. Otherwise, the drive will become stuck and be difficult to reassemble.

Step 12

              Keyboard

Insert one of the pry tools under a top corner and the other tool under the side of the same corner. Make sure to get under the metal of the keyboard, not just the first layer of plastic. Then pry the corner down and out from under the little overhang its sitting under.
Next, slide the pry tool on the top over to the next overhang and insert the second tool on the other side. Push down and pry out the keyboard.
Repeat the same process all the way down to the opposite corner.

Insert one of the pry tools under a top corner and the other tool under the side of the same corner. Make sure to get under the metal of the keyboard, not just the first layer of plastic. Then pry the corner down and out from under the little overhang its sitting under.

Next, slide the pry tool on the top over to the next overhang and insert the second tool on the other side. Push down and pry out the keyboard.

Repeat the same process all the way down to the opposite corner.

Step 13

Once the keyboard is free, lift it up slightly and release the cable connection underneath.

Once the keyboard is free, lift it up slightly and release the cable connection underneath.

Step 14

Last, remove the keyboard completely from the computer.

Last, remove the keyboard completely from the computer.

Step 15

              Random Access Memory (RAM)

Push back on the silver clips shown in the picture until you hear/feel a pop.

Push back on the silver clips shown in the picture until you hear/feel a pop.

Step 16

Pull back on the RAM card and remove it.
Repeat for the lower RAM card.

Pull back on the RAM card and remove it.

Repeat for the lower RAM card.

Step 17

              Upper Case

Remove the six screws from the outer lower case.
Remove the four screws from the hinges.
Remove the three screws on the inner lower case.
Remove the three screws from the optical drive area.

Remove the six screws from the outer lower case.

Remove the four screws from the hinges.

Remove the three screws on the inner lower case.

Remove the three screws from the optical drive area.

Step 18

Remove the two screws from the metal frame.

Remove the two screws from the metal frame.

Step 19

Pull the two bundled cables away from the connector in the same direction as the individual wires are running.
Potential for device damage: Pull evenly on the full width of the cable so that no individual wires are overly strained.
Pull the no-fuss ribbon cable straight out of the connector.
Potential for device damage: These kinds of connectors are fairly rare, so check carefully for a way to release the connector before you resort to pulling on the ribbon cable.
Pull the single bundled cable away from the connector in the same direction as the individual wires are running.
Potential for device damage: Pull evenly on the full width of the cable so that no individual wires are overly strained.

Pull the two bundled cables away from the connector in the same direction as the individual wires are running.

Potential for device damage: Pull evenly on the full width of the cable so that no individual wires are overly strained.

Pull the no-fuss ribbon cable straight out of the connector.

Potential for device damage: These kinds of connectors are fairly rare, so check carefully for a way to release the connector before you resort to pulling on the ribbon cable.

Pull the single bundled cable away from the connector in the same direction as the individual wires are running.

Step 20

Lift up and remove the upper case.

Lift up and remove the upper case.

Step 21

              Ports (USB/Audio Jack/Microphone Jack/E-SATA)

Step 22

Pull the cable away from the connector in the same direction as the individual wires.
Pull evenly on the full width of the cable so that no individual wires are overly strained.

Pull the cable away from the connector in the same direction as the individual wires.

Pull evenly on the full width of the cable so that no individual wires are overly strained.

Step 23

Lift up and remove the port panel.

Lift up and remove the port panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Kelly Greeling

Member since: 02/07/2017

1,028 Reputation

                                      10 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of Illinois Urbana-Champaign, Team 1-1, Scrogum Spring 2017                        

                                                  Member of University of Illinois Urbana-Champaign, Team 1-1, Scrogum Spring 2017 



                    UICU-SCROGUM-S17S1G1                     


                                            3 Members                     


                                            19 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team