Difficulty
Moderate
Steps
21
Time Required
10 - 15 minutes
Sections
5
- Back Panel
- 3 steps
- Battery
- 3 steps
- Cooling Fan
- 3 steps
- Wireless Card
- 4 steps
- Motherboard
- 8 steps
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackAsus VivoBook Q200E-BSI3T08
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Turn off the computer and unplug the charge cable.
- If the computer is on or plugged in, it could cause electric shock.
- Turn the computer upside down.
Turn off the computer and unplug the charge cable.
If the computer is on or plugged in, it could cause electric shock.
Turn the computer upside down.
1024
Step 2
- Remove the nine Philips #00 screws holding the back panel in place (four 5.6mm, four 7.7mm, and one 9.2mm).
Remove the nine Philips #00 screws holding the back panel in place (four 5.6mm, four 7.7mm, and one 9.2mm).
Step 3
- Use a plastic opening tool to gently remove the back panel.
Use a plastic opening tool to gently remove the back panel.
Step 4
Battery
- Remove the eight 4.7mm Philips #00 screws holding the battery in place.
Remove the eight 4.7mm Philips #00 screws holding the battery in place.
Step 5
- The battery is attached by a set of wires.
- Use your finger to disconnect the set of wires. It should come off very easily.
The battery is attached by a set of wires.
Use your finger to disconnect the set of wires. It should come off very easily.
Step 6
- Now just lift the battery out of place.
Now just lift the battery out of place.
Step 7
Cooling Fan
- Unscrew the five 4.9mm screws holding the cooling fan in place using a Phillips #0 screwdriver.
Unscrew the five 4.9mm screws holding the cooling fan in place using a Phillips #0 screwdriver.
Step 8
- Unplug the power bus for the fan.
Unplug the power bus for the fan.
Step 9
- Lift up and remove the cooling fan from the slot.
Lift up and remove the cooling fan from the slot.
Step 10
Wireless Card
- Locate wireless card next to battery.
Locate wireless card next to battery.
Step 11
- Remove the one 4.9mm screw that holds the wireless card in place with a Phillips #00 screwdriver.
Remove the one 4.9mm screw that holds the wireless card in place with a Phillips #00 screwdriver.
Step 12
- Unplug the black coaxial cable from the wireless card.
Unplug the black coaxial cable from the wireless card.
Step 13
- Pull the wireless card from connector slot.
Pull the wireless card from connector slot.
Step 14
Motherboard
- Locate the motherboard under the cooling fan.
Locate the motherboard under the cooling fan.
Step 15
- Unscrew the two 5.9mm screws on the PCB board with a Phillips #0 screwdriver.
Unscrew the two 5.9mm screws on the PCB board with a Phillips #0 screwdriver.
Step 16
- Remove the PCB board from the motherboard.
Remove the PCB board from the motherboard.
Step 17
- Unscrew the four 5.9mm hard drive bracket screws with a Phillips #0 screwdriver.
Unscrew the four 5.9mm hard drive bracket screws with a Phillips #0 screwdriver.
Step 18
- Unscrew the four 5.9mm screws with a Phillips #0 screwdriver.
- Next, carefully lift the LAN bracket out of the slot.
Unscrew the four 5.9mm screws with a Phillips #0 screwdriver.
Next, carefully lift the LAN bracket out of the slot.
Step 19
- Remove the five 5.9mm screws holding the motherboard in place with a Phillips #0 screwdriver.
- Remove the five 3.5mm screws holding the motherboard with a Phillips #00 screwdriver.
Remove the five 5.9mm screws holding the motherboard in place with a Phillips #0 screwdriver.
Remove the five 3.5mm screws holding the motherboard with a Phillips #00 screwdriver.
Step 20
- Carefully lift the motherboard up out of the slot.
Carefully lift the motherboard up out of the slot.
Step 21
- Locate and unplug the power bus from the motherboard.
- The motherboard can now be replaced.
Locate and unplug the power bus from the motherboard.
The motherboard can now be replaced.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Mitchell Jackson
Member since: 05/17/2017
742 Reputation
7 Guides authored
Badges:
6
+3 more badges
Team
IUPUI, Team S4-G4, Wilson Summer 2017
Member of IUPUI, Team S4-G4, Wilson Summer 2017
IUPUI-WILSON-SU17S4G4
4 Members
7 Guides authored
Gs Mobile - Aug 23, 2018
Reply
Very useful tutorial with nice photos indicating even different type of screws n different color..
This was more useful than a YouTube video..
I just replaced my mother board..
Thank you and God bless u for ur effort..
