Difficulty
Difficult
Steps
18
Time Required
40 minutes
Sections
4
- Battery
- 5 steps
- Hard Drive
- 2 steps
- Motherboard
- 8 steps
- Display
- 3 steps
Flags
0
BackAsus VivoBook X202E-DB21T
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Flip the device such that the labels are on top.
- Use a Phillips #1 screwdriver to remove the four 8mm screws near the back.
- Use the same screwdriver to remove the four 5mm screws in the front.
- Use the same screwdriver to remove the single 9mm screw in the center.
- Make sure that the device is powered down and unplugged.
Flip the device such that the labels are on top.
Use a Phillips #1 screwdriver to remove the four 8mm screws near the back.
Use the same screwdriver to remove the four 5mm screws in the front.
Use the same screwdriver to remove the single 9mm screw in the center.
Make sure that the device is powered down and unplugged.
1024
Step 2
- Remove the back cover by gently prying with a spudger.
Remove the back cover by gently prying with a spudger.
Step 3
- Remove the eight 5mm screws using a Phillips #1 screwdriver.
- Do not puncture the battery.
Remove the eight 5mm screws using a Phillips #1 screwdriver.
Do not puncture the battery.
Step 4
- Disconnect the battery ribbon cable from the motherboard.
Disconnect the battery ribbon cable from the motherboard.
Step 5
- Remove the battery from the laptop.
Remove the battery from the laptop.
Step 6
Hard Drive
- Unscrew the three 4mm screws holding the hard drive to the board.
Unscrew the three 4mm screws holding the hard drive to the board.
Step 7
- Pull on the tab on the left side of the hard drive and slowly disconnect it from the board.
Pull on the tab on the left side of the hard drive and slowly disconnect it from the board.
Step 8
Motherboard
- Unscrew the five 5mm screws holding the left board together.
Unscrew the five 5mm screws holding the left board together.
Step 9
- Unplug the two connectors on the left board.
Unplug the two connectors on the left board.
Step 10
- Remove the single 3mm screw from the sound chip.
- Unplug the sound chip.
- Remove the sound chip.
Remove the single 3mm screw from the sound chip.
Unplug the sound chip.
Remove the sound chip.
Step 11
- Remove the six 4mm screws holding the fan and CPU cover.
Remove the six 4mm screws holding the fan and CPU cover.
Step 12
- Unplug the fan.
- Remove the fan and CPU cover.
Unplug the fan.
Remove the fan and CPU cover.
Step 13
- Unscrew the nine 4mm screws holding the right board together.
Unscrew the nine 4mm screws holding the right board together.
Step 14
- Remove the two remaining connectors on the board.
Remove the two remaining connectors on the board.
Step 15
- Remove the right board.
Remove the right board.
Step 16
Display
- Unscrew the three 5mm screws holding the display to the main body of the computer.
Unscrew the three 5mm screws holding the display to the main body of the computer.
Step 17
- Unhook the cables coming from the display.
Unhook the cables coming from the display.
Step 18
- Tilt the screen away from the main body of the computer.
- Remove the screen.
Tilt the screen away from the main body of the computer.
Remove the screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
John Thomas
Member since: 01/13/2019
756 Reputation
6 Guides authored
Badges:
10
+7 more badges
Team
Eastern Washington University, Team S1-G5, Crawford Winter 2019
Member of Eastern Washington University, Team S1-G5, Crawford Winter 2019
EWU-CRAWFORD-W19S1G5
4 Members
7 Guides authored
