Difficulty
Moderate
Steps
7
Time Required
10 - 20 minutes
Sections
1
- Battery
- 7 steps
Flags
0
BackAsus VivoTab Smart
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Once you are done, calibrate your newly installed battery by draining it below 10% and then charging it uninterrupted to 100%.
What you need
Step 1
Battery
- Power off the device before you begin disassembly.
- Place the device face down on a flat surface.
- Remove the back panel with the plastic opening tool by sliding the tool around the edge of the panel.
Power off the device before you begin disassembly.
Place the device face down on a flat surface.
Remove the back panel with the plastic opening tool by sliding the tool around the edge of the panel.
1024
Step 2
- Remove the tape covering the 3 ribbons by peeling it off with your hands or with the tweezers.
- Carefully detach the ribbons from the device’s motherboard by pulling outward using tweezers.
Remove the tape covering the 3 ribbons by peeling it off with your hands or with the tweezers.
Carefully detach the ribbons from the device’s motherboard by pulling outward using tweezers.
Step 3
- The Philips #00 Screwdriver listed in the recommended tools will fit all the screws.
- Remove the tape covering the areas marked by the black arrows
- Remove two 3.7 mm Phillips #00 screws
- Remove eleven 2.7 mm Phillips #00 screws
The Philips #00 Screwdriver listed in the recommended tools will fit all the screws.
Remove the tape covering the areas marked by the black arrows
Remove two 3.7 mm Phillips #00 screws
Remove eleven 2.7 mm Phillips #00 screws
Step 4
- Be careful not to damage the speaker wire.
- Gently unplug the speaker from the motherboard by grabbing the wire near the plastic white plug with tweezers and gently pulling.
- Lift up on the speaker with your fingers to remove it.
Be careful not to damage the speaker wire.
Gently unplug the speaker from the motherboard by grabbing the wire near the plastic white plug with tweezers and gently pulling.
Lift up on the speaker with your fingers to remove it.
Step 5
- Gently lift the battery pressure plate off of the motherboard.
Gently lift the battery pressure plate off of the motherboard.
Step 6
- Use tweezers to separate the battery tray from the device
- Lift the battery tray from the device using your hands.
Use tweezers to separate the battery tray from the device
Lift the battery tray from the device using your hands.
Step 7
- The battery is secured to the tray by a strong adhesive. Take care not to bend the tray when removing the battery.
- Detach the battery from the tray by pulling the battery up from the tray with your hands.
- If it is very difficult to lift the battery from the tray, you can use a blow dryer to heat the back side of the tray. This will weaken the adhesive and make it easier to remove.
The battery is secured to the tray by a strong adhesive. Take care not to bend the tray when removing the battery.
Detach the battery from the tray by pulling the battery up from the tray with your hands.
If it is very difficult to lift the battery from the tray, you can use a blow dryer to heat the back side of the tray. This will weaken the adhesive and make it easier to remove.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 6 other contributors
Zach Hatten
Member since: 10/06/2016
548 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
USF Tampa, Team 2-4, Sullivan Fall 2016
Member of USF Tampa, Team 2-4, Sullivan Fall 2016
USFT-SULLIVAN-F16S2G4
4 Members
5 Guides authored
Albert einstein - Jan 4, 2018
Reply
Hi
So where is the next step ?!
Please answer to me. This is so
