Difficulty
Moderate
Steps
13
Time Required
20 - 30 minutes
Sections
4
- Keyboard Assembly
- 2 steps
- Battery
- 5 steps
- Fan
- 3 steps
- Motherboard
- 3 steps
Flags
0
BackAsus X200MA
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Remove the following six screws:
- Six 4 mm screws using a Phillips #0 screwdriver.
- Remove the following one screw:
- One 14 mm screw using a Phillips #0 screwdriver.
- The 14mm screw goes in the center.
Remove the following six screws:
Six 4 mm screws using a Phillips #0 screwdriver.
Remove the following one screw:
One 14 mm screw using a Phillips #0 screwdriver.
The 14mm screw goes in the center.
1024
Step 2
- Use a plastic or metal spudger to separate the keyboard from the back panel and lift the keyboard out of place.
Use a plastic or metal spudger to separate the keyboard from the back panel and lift the keyboard out of place.
Step 3
Battery
- Take two rubber caps off the back side of the laptop.
Take two rubber caps off the back side of the laptop.
Step 4
- Remove the following two screws under the rubber caps.
- Two 14 mm screws using the Phillips #0 screw driver.
Remove the following two screws under the rubber caps.
Two 14 mm screws using the Phillips #0 screw driver.
Step 5
- Flip up the following:
- The two latches holding the two cables shown(white and black)
- Pull the cables free from the latches
- Lift the keyboard from the computer
Flip up the following:
The two latches holding the two cables shown(white and black)
Pull the cables free from the latches
Lift the keyboard from the computer
Step 6
- Remove the following screws from the inside of the laptop:
- Two 4 mm screws using the Phillips #0 phillips screwdriver.
- One 5 mm screw using the Phillips #0 Phillips screwdriver located in the center a little below the battery.
Remove the following screws from the inside of the laptop:
Two 4 mm screws using the Phillips #0 phillips screwdriver.
One 5 mm screw using the Phillips #0 Phillips screwdriver located in the center a little below the battery.
Step 7
- Slide the battery up and out.
Slide the battery up and out.
Step 8
Fan
- Remove the Two 4 mm screws using Phillips #0 phillips screwdriver.
Remove the Two 4 mm screws using Phillips #0 phillips screwdriver.
Step 9
- Unplug the set of wires located at bottom corner on fan.
Unplug the set of wires located at bottom corner on fan.
Step 10
- Lift up and out to completely the remove fan component.
Lift up and out to completely the remove fan component.
Step 11
Motherboard
- Use Phillips #0 screwdriver to remove the eight 4.0 mm screws.
Use Phillips #0 screwdriver to remove the eight 4.0 mm screws.
Step 12
- Pull back the blue ribbon, freeing it from the latch.
Pull back the blue ribbon, freeing it from the latch.
Step 13
- Lift and pull the motherboard out from the hard drive and remove it from the base plate.
Lift and pull the motherboard out from the hard drive and remove it from the base plate.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Alli Krininger
Member since: 11/11/2019
391 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
IUPUI, Team S2-G4, Stella Fall 2019
Member of IUPUI, Team S2-G4, Stella Fall 2019
IUPUI-STELLA-F19S2G4
4 Members
3 Guides authored
