Difficulty

Moderate

Steps

15

Time Required

                          20 minutes - 1 hour

Sections

3

  • Keyboard Assembly
  • 2 steps
  • Battery
  • 5 steps
  • Screen
  • 8 steps

Flags

0

  • BackAsus X200MA

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Remove the following six screws:
  • Six 4 mm screws using a Phillips #0 screwdriver.
  • Remove the following one screw:
  • One 14 mm screw using a Phillips #0 screwdriver.
  • The 14mm screw goes in the center.

Remove the following six screws:

Six 4 mm screws using a Phillips #0 screwdriver.

Remove the following one screw:

One 14 mm screw using a Phillips #0 screwdriver.

The 14mm screw goes in the center.

1024

Step 2

  • Use a plastic or metal spudger to separate the keyboard from the back panel and lift the keyboard out of place.

Use a plastic or metal spudger to separate the keyboard from the back panel and lift the keyboard out of place.

Step 3

              Battery
  • Take two rubber caps off the back side of the laptop.

Take two rubber caps off the back side of the laptop.

Step 4

  • Remove the following two screws under the rubber caps.
  • Two 14 mm screws using the Phillips #0 screw driver.

Remove the following two screws under the rubber caps.

Two 14 mm screws using the Phillips #0 screw driver.

Step 5

  • Flip up the following:
  • The two latches holding the two cables shown(white and black)
  • Pull the cables free from the latches
  • Lift the keyboard from the computer

Flip up the following:

The two latches holding the two cables shown(white and black)

Pull the cables free from the latches

Lift the keyboard from the computer

Step 6

  • Remove the following screws from the inside of the laptop:
  • Two 4 mm screws using the Phillips #0 phillips screwdriver.
  • One 5 mm screw using the Phillips #0 Phillips screwdriver located in the center a little below the battery.

Remove the following screws from the inside of the laptop:

Two 4 mm screws using the Phillips #0 phillips screwdriver.

One 5 mm screw using the Phillips #0 Phillips screwdriver located in the center a little below the battery.

Step 7

  • Slide the battery up and out.

Slide the battery up and out.

Step 8

              Screen
  • Remove the following four 3 mm screws using the Phillips #0 screwdriver.

Remove the following four 3 mm screws using the Phillips #0 screwdriver.

Step 9

  • Lift and separate the screen from the base plate.

Lift and separate the screen from the base plate.

Step 10

  • Insert the metal spudger into the side of the screen casing. Work the spudger around the perimeter of the casing in a rowing motion in order to release the plastic clips holding the casing together.
  • Place a finger in the space between the casing while undoing the clips to keep the casing from re-closing.

Insert the metal spudger into the side of the screen casing. Work the spudger around the perimeter of the casing in a rowing motion in order to release the plastic clips holding the casing together.

Place a finger in the space between the casing while undoing the clips to keep the casing from re-closing.

Step 11

  • Lift the half of the casing with the screen away from the other half of the casing and place the screen half on a work space by itself.

Lift the half of the casing with the screen away from the other half of the casing and place the screen half on a work space by itself.

Step 12

  • Remove the following six 3 mm screws using the Phillips #0 screwdriver.

Remove the following six 3 mm screws using the Phillips #0 screwdriver.

Step 13

  • Use the jimmy tool to peel the following stickers from the screen:
  • The silver sticker near the bottom.
  • The information sticker near the top.

Use the jimmy tool to peel the following stickers from the screen:

The silver sticker near the bottom.

The information sticker near the top.

Step 14

  • Lift the latch holding the component in place.
  • Remove the component by pulling in the direction of the arrows.

Lift the latch holding the component in place.

Remove the component by pulling in the direction of the arrows.

Step 15

  • Lift the screen from the casing and place the two next to one another.

Lift the screen from the casing and place the two next to one another.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Alli Krininger

Member since: 11/11/2019

391 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       IUPUI, Team S2-G4, Stella Fall 2019                        

                                                  Member of IUPUI, Team S2-G4, Stella Fall 2019 



                    IUPUI-STELLA-F19S2G4                     


                                            4 Members                     


                                            3 Guides authored