Difficulty

Moderate

Steps

28

Time Required

                          10 - 15 minutes

Sections

7

  • Keyboard Plate Cover
  • 5 steps
  • Hard Drive
  • 3 steps
  • Spacer
  • 2 steps
  • WiFi Card
  • 3 steps
  • Battery
  • 1 step
  • Motherboard
  • 5 steps
  • Front Display Bezel
  • 9 steps

Flags

0

  • BackAsus X551CA

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard Plate Cover
  • Power off and unplug your laptop before you begin.
  • Turn the laptop upside-down and remove the following screws using a Phillips #0 driver:
  • Two 9.5 mm screws in the middle of the back edge, and one 9.5 mm screw in the right edge
  • Two 4.3 mm screws in the back corners
  • One 17.5 mm screw at the left edge near the optical drive
  • Three 4.3 mm screws in the front edge

Power off and unplug your laptop before you begin.

Turn the laptop upside-down and remove the following screws using a Phillips #0 driver:

Two 9.5 mm screws in the middle of the back edge, and one 9.5 mm screw in the right edge

Two 4.3 mm screws in the back corners

One 17.5 mm screw at the left edge near the optical drive

Three 4.3 mm screws in the front edge

1024

Step 2

  • Use the plastic opening tool to separate the keyboard plate cover from the bottom cover. In order to do this, insert the plastic opening tool in between the keyboard plate cover and the bottom cover, then slide along edges to pry open.

Use the plastic opening tool to separate the keyboard plate cover from the bottom cover. In order to do this, insert the plastic opening tool in between the keyboard plate cover and the bottom cover, then slide along edges to pry open.

Step 3

  • Locate the three ribbons connecting the keyboard plate cover to the bottom cover.

Locate the three ribbons connecting the keyboard plate cover to the bottom cover.

Step 4

  • Invert the laptop in order to gain access to the ribbons.
  • Remove each ribbon by flipping the small white plastic flap up and gently pulling on the ribbon.

Invert the laptop in order to gain access to the ribbons.

Remove each ribbon by flipping the small white plastic flap up and gently pulling on the ribbon.

Step 5

  • Now that the ribbons have been detached from the bottom cover, carefully remove the keyboard plate cover. Once it has been removed, place it in a safe and moisture free area so it does not get damaged.

Now that the ribbons have been detached from the bottom cover, carefully remove the keyboard plate cover. Once it has been removed, place it in a safe and moisture free area so it does not get damaged.

Step 6

              Hard Drive
  • Unscrew the three 5.5 mm Phillips #0 screws with the Phillips #0 Screwdriver.

Unscrew the three 5.5 mm Phillips #0 screws with the Phillips #0 Screwdriver.

Step 7

  • Once the screws have been removed, place your fingers on the left corners and push the hard drive towards the right edge of the laptop (relative to the picture).

Once the screws have been removed, place your fingers on the left corners and push the hard drive towards the right edge of the laptop (relative to the picture).

Step 8

  • Once it is free, remove the hard drive from its internal cavity.

Once it is free, remove the hard drive from its internal cavity.

Step 9

              Spacer
  • Using the Phillips #0 Screwdriver, unscrew the 5.5 mm Phillips #0 screw that holds the spacer in place.

Using the Phillips #0 Screwdriver, unscrew the 5.5 mm Phillips #0 screw that holds the spacer in place.

Step 10

  • Remove the spacer from the laptop by gently sliding it towards the right edge of the laptop.

Remove the spacer from the laptop by gently sliding it towards the right edge of the laptop.

Step 11

              WiFi Card
  • Use the Phillips #0 Screwdriver to unscrew the 3.2 mm Phillips #0 screw which attaches the WiFi card to the motherboard.

Use the Phillips #0 Screwdriver to unscrew the 3.2 mm Phillips #0 screw which attaches the WiFi card to the motherboard.

Step 12

  • Disconnect the Wifi card from the motherboard by gently sliding it towards the right edge of the laptop.

Disconnect the Wifi card from the motherboard by gently sliding it towards the right edge of the laptop.

Step 13

  • Remove each of the two small antenna connections by disconnecting one wire at a time. Each wire should easily unsnap from the Wifi card.

Remove each of the two small antenna connections by disconnecting one wire at a time. Each wire should easily unsnap from the Wifi card.

Step 14

              Battery
  • Remove the battery from the laptop by applying pressure on both ends and lifting it out of the case.

Remove the battery from the laptop by applying pressure on both ends and lifting it out of the case.

Step 15

              Motherboard
  • With the Phillips #0 Screwdriver, remove the nine 5.5 mm Phillips #0 screws which hold the motherboard in place.

With the Phillips #0 Screwdriver, remove the nine 5.5 mm Phillips #0 screws which hold the motherboard in place.

Step 16

  • Now, locate the two wires connected to the motherboard.

Now, locate the two wires connected to the motherboard.

Step 17

  • Remove the wires by easily pulling them parallel to the motherboard’s surface.
  • The wires are very fragile. Be sure to pull carefully so that they do not break!

Remove the wires by easily pulling them parallel to the motherboard’s surface.

The wires are very fragile. Be sure to pull carefully so that they do not break!

Step 18

  • Remove the LCD display connection by gently pulling on the attached wire.
  • Gently lift any tape that may be holding the connection.

Remove the LCD display connection by gently pulling on the attached wire.

Gently lift any tape that may be holding the connection.

Step 19

  • Remove the motherboard from the case by gently lifting it upward.

Remove the motherboard from the case by gently lifting it upward.

Step 20

              Front Display Bezel
  • Locate both of the hinges that connect the monitor to the bottom plate cover.

Locate both of the hinges that connect the monitor to the bottom plate cover.

Step 21

  • Use the Phillips #0 screwdriver to unscrew the two 4.8 mm Phillips #0 screws on the right hinge, and the one 4.8 mm Phillips #0 screw on the left hinge.

Use the Phillips #0 screwdriver to unscrew the two 4.8 mm Phillips #0 screws on the right hinge, and the one 4.8 mm Phillips #0 screw on the left hinge.

Step 22

  • Once the screws are removed, the monitor should easily lift away from the bottom plate cover

Once the screws are removed, the monitor should easily lift away from the bottom plate cover

Step 23

  • Locate the two stickers that cover up the screws that hold the front bezel in place

Locate the two stickers that cover up the screws that hold the front bezel in place

Step 24

  • Use a pair of tweezers to remove these stickers.
  • The stickers can be difficult to grasp with the tweezers so do not be discouraged when trying to remove them!

Use a pair of tweezers to remove these stickers.

The stickers can be difficult to grasp with the tweezers so do not be discouraged when trying to remove them!

Step 25

  • Once the stickers are removed, the two screws that hold the front bezel in place will be exposed.

Once the stickers are removed, the two screws that hold the front bezel in place will be exposed.

Step 26

  • Use the Phillips #0 screwdriver to remove the two 4.8 mm Phillips #0 screws.

Use the Phillips #0 screwdriver to remove the two 4.8 mm Phillips #0 screws.

Step 27

  • Once the screws are taken out, the front bezel is ready to be removed.
  • Insert the Plastic Opening Tool inbetween the front and back bezels and slide along the edges to pry open.
  • Gently use hands if necessary to separate the front bezel from the back.

Once the screws are taken out, the front bezel is ready to be removed.

Insert the Plastic Opening Tool inbetween the front and back bezels and slide along the edges to pry open.

Gently use hands if necessary to separate the front bezel from the back.

Step 28

  • Once pried away from the back bezel, the front bezel will easily lift away from the LCD.

Once pried away from the back bezel, the front bezel will easily lift away from the LCD.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 4 other contributors 


                    Josh

Member since: 04/10/2014

2,922 Reputation

                                      12 Guides authored                  



                       Badges:
                       21







                                                        +18 more badges

Team

                       Cal Poly, Team 7-22, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 7-22, Regan Spring 2014 



                    CPSU-REGAN-S14S7G22                     


                                            5 Members                     


                                            15 Guides authored