Difficulty
Moderate
Steps
7
Time Required
15 - 30 minutes
Sections
1
- SSD
- 7 steps
Flags
0
BackAsus Zenbook UX303L
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
SSD
- Make sure the device is turned off and disconnected from the battery charger.
Make sure the device is turned off and disconnected from the battery charger.
1024
Step 2
- Remove all nine screws from the bottom of the device using a T5 screwdriver.
- Remove two additional screws, if present, from beneath the rubber pads. (Pry up each rubber pad to access its screw.)
- Carefully remove the bottom cover. The cover doesn’t just lift up, you have to lift it to a approx. 45° angle, then pull towards the exterior (there are two small plastic claws that maintain the cover attached)
Remove all nine screws from the bottom of the device using a T5 screwdriver.
Remove two additional screws, if present, from beneath the rubber pads. (Pry up each rubber pad to access its screw.)
Carefully remove the bottom cover. The cover doesn’t just lift up, you have to lift it to a approx. 45° angle, then pull towards the exterior (there are two small plastic claws that maintain the cover attached)
Step 3
- Remove the five screws attaching the battery pack by using a PH-1 screwdriver.
Remove the five screws attaching the battery pack by using a PH-1 screwdriver.
Step 4
- Unhook the black, red, and white switch using the tweezers.
Unhook the black, red, and white switch using the tweezers.
Step 5
- Detach the positive and negative black, white, yellow, and red switch with the use of tweezers.
Detach the positive and negative black, white, yellow, and red switch with the use of tweezers.
Step 6
- Unhook the black and white coiled wire using the tweezers.
Unhook the black and white coiled wire using the tweezers.
Step 7
- Remove the 3 screws surrounding the hard drive using the PH-1 screwdriver.
- Gently lift and detach the hard drive, and pull it out.
- If your model has never been opened, you might have this “cushion sticker” that makes it difficult to unplug the hard drive. You can just peel it and put it back later.
Remove the 3 screws surrounding the hard drive using the PH-1 screwdriver.
Gently lift and detach the hard drive, and pull it out.
If your model has never been opened, you might have this “cushion sticker” that makes it difficult to unplug the hard drive. You can just peel it and put it back later.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
21 other people completed this guide.
Author
with 10 other contributors
Cindy Lopez
Member since: 10/13/2015
642 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
Sam Houston State, Team 1-3, Blackburne Fall 2015
Member of Sam Houston State, Team 1-3, Blackburne Fall 2015
SHSU-BLACKBURNE-F15S1G3
3 Members
4 Guides authored
Greg - Nov 3, 2018
Reply
This guide worked fine for me. I have two suggestions that made my disassembly easier.
First, I used the standard blue guitar pick to gently pop the back cover off near the hinge. Nothing special here.
Second, the power connector in Step 5 lifts up to disconnect. I found using the blue pry bar to lift the side of the connector much easier than tweezers.
Good, clear, complete guide.
Chawit Leosrisook - Dec 24, 2018
Reply
Great guide, worked for me.
Additionally, for Step 7, the 3 screws might be hidden under cushion stickers. These can be peeled off and put back later.
Steff - Nov 29, 2019
Reply
Mein Laptop geht nach dem Umbau nicht mehr einzuschalten. Selbst die kleine Akku LED leuchtet nicht mehr, sobald das Netzkabel dran gesteckt ist. :(
