Difficulty

Moderate

Steps

13

Time Required

                          10 - 15 minutes

Sections

2

  • Battery
  • 7 steps
  • Back Camera
  • 6 steps

Flags

0

  • BackAsus ZenFone 3 Zoom

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Using a pair of tweezers, pull put the SIM card tray and set it to the side.

Using a pair of tweezers, pull put the SIM card tray and set it to the side.

1024

Step 2

  • Remove the two 2 mm screws using a Torx T2 screwdriver.

Remove the two 2 mm screws using a Torx T2 screwdriver.

Step 3

  • Insert a prying tool between the screen and the metal backing of the phone at the bottom to remove backing from phone.
  • There will be a thin film connecting the two pieces. You do not need to remove this. Just fold the two pieces apart with the inside facing up.

Insert a prying tool between the screen and the metal backing of the phone at the bottom to remove backing from phone.

There will be a thin film connecting the two pieces. You do not need to remove this. Just fold the two pieces apart with the inside facing up.

Step 4

  • Remove the two 3 mm screws, using the Phillips #00 screwdriver, on the silver band at the top of the battery and remove the band.

Remove the two 3 mm screws, using the Phillips #00 screwdriver, on the silver band at the top of the battery and remove the band.

Step 5

  • Peel back the silver tape.

Peel back the silver tape.

Step 6

  • Disconnect the battery connections.

Disconnect the battery connections.

Step 7

  • Pry and remove the battery.
  • The underside of the battery is adhesive so make sure to pry the battery off gently.

Pry and remove the battery.

The underside of the battery is adhesive so make sure to pry the battery off gently.

Step 8

              Back Camera
  • Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side.

Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side.

Step 9

  • Remove the 3 mm screws, using the Phillips #00 screwdriver, from the metal piece around the camera.

Remove the 3 mm screws, using the Phillips #00 screwdriver, from the metal piece around the camera.

Step 10

  • Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver.

Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver.

Step 11

  • Unplug the two wires at the bottom of the circuit board.

Unplug the two wires at the bottom of the circuit board.

Step 12

  • Remove the circuit board.

Remove the circuit board.

Step 13

  • Unplug the camera.

Unplug the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Henry Barrett

Member since: 09/10/2018

537 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of Alabama, Team S2-G7, Bedsole Fall 2018                        

                                                  Member of University of Alabama, Team S2-G7, Bedsole Fall 2018 



                    UA-BEDSOLE-F18S2G7                     


                                            4 Members                     


                                            10 Guides authored