Difficulty

Moderate

Steps

8

Time Required

                          45 minutes

Sections

2

  • Battery
  • 7 steps
  • Touch Sensor
  • 1 step

Flags

6

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Missed a Step

Oops! This guide is currently missing some important steps.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackAsus ZenFone 5

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

This guide misses a step in disconnecting the touch sensor from the motherboard. If you do not reconnect the press fit connector for the fingerprint sensor during reassembly, it will not function.

What you need

Step 1

              Battery
  • Heat up the iOpener in the microwave for 30 seconds.
  • Caution: when the iOpener is heated up, hold it by the sides to prevent bodily harm.

Heat up the iOpener in the microwave for 30 seconds.

Caution: when the iOpener is heated up, hold it by the sides to prevent bodily harm.

1024

Step 2

  • Place the iOpener on the side of the phone until the iOpener gets cool (approximately 10-15 minutes).
  • Reheat the iOpener and reapply it to the other side of the phone.

Place the iOpener on the side of the phone until the iOpener gets cool (approximately 10-15 minutes).

Reheat the iOpener and reapply it to the other side of the phone.

Step 3

  • Gently slide the jimmy along the edges of the phone to break the adhesive.
  • Use opening picks and the opening tool to pry the back cover off.
  • The use of metal tools as shown in the photos is potentially dangerous as the battery is exposed along the edges of the case and risk of puncture is high. Choose an ESD safe tool instead.
  • There are 6 different tabs on each side of the phone that might take force to get apart.
  • Repeat the heating and prying process until the back cover can be fully removed.

Gently slide the jimmy along the edges of the phone to break the adhesive.

Use opening picks and the opening tool to pry the back cover off.

The use of metal tools as shown in the photos is potentially dangerous as the battery is exposed along the edges of the case and risk of puncture is high. Choose an ESD safe tool instead.

There are 6 different tabs on each side of the phone that might take force to get apart.

Repeat the heating and prying process until the back cover can be fully removed.

Step 4

  • Use the #00 phillips head to take out the six phillips #00 3.175mm screws on the top cover plate.
  • Use the spudger to release the clasps along the edge of the top plate.

Use the #00 phillips head to take out the six phillips #00 3.175mm screws on the top cover plate.

Use the spudger to release the clasps along the edge of the top plate.

Step 5

  • Disconnect the press fit connector located near the upper right corner of the battery to disengage the battery from the motherboard.

Disconnect the press fit connector located near the upper right corner of the battery to disengage the battery from the motherboard.

Step 6

  • Use the same screwdriver to remove the five phillips #00 3.96mm screws along the bottom plate.
  • Use the spudger to pry the bottom plate off.

Use the same screwdriver to remove the five phillips #00 3.96mm screws along the bottom plate.

Use the spudger to pry the bottom plate off.

Step 7

  • Pull on the two black tabs on the bottom of the battery until the battery is released.
  • Gently pull the battery out of its socket.

Pull on the two black tabs on the bottom of the battery until the battery is released.

Gently pull the battery out of its socket.

Step 8

              Touch Sensor
  • On the back shell of the phone, push with pressure on the touch sensor until it pops out.

On the back shell of the phone, push with pressure on the touch sensor until it pops out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Nathan Foster

Member since: 07/08/2019

612 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Embry-Riddle Aeronautical University, Team S3-G27, Watkins Summer 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S3-G27, Watkins Summer 2019 



                    ERAU-WATKINS-SU19S3G27                     


                                            4 Members                     


                                            9 Guides authored

Alex Watkins - Aug 1, 2019

Reply

I might replace the introduction picture in this guide for one that doesn’t have the background missing on the right side.