Difficulty

Difficult

Steps

20

Time Required

                          45 minutes

Sections

6

  • Back Cover
  • 2 steps
  • Battery
  • 2 steps
  • Motherboard
  • 7 steps
  • Front Camera
  • 1 step
  • Screen
  • 7 steps
  • Screen Digitizer
  • 1 step

Flags

0

  • BackATT Trek HD

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • To separate the screen from the back panel, run the plastic opening tool along the outer edge of the device.

To separate the screen from the back panel, run the plastic opening tool along the outer edge of the device.

1024

Step 2

  • Pull the screen away from the back panel.

Pull the screen away from the back panel.

Step 3

              Battery
  • Use a Phillips #00 screwdriver to remove the six 2.5 mm screws located around the perimeter of the battery.

Use a Phillips #00 screwdriver to remove the six 2.5 mm screws located around the perimeter of the battery.

Step 4

  • Use the plastic opening tool to disconnect the black battery connector.
  • Gently lift the battery out of the device.

Use the plastic opening tool to disconnect the black battery connector.

Gently lift the battery out of the device.

Step 5

              Motherboard
  • Using a Phillips #00 screwdriver, remove the seven 1 mm screws on the green perimeter of the motherboard.

Using a Phillips #00 screwdriver, remove the seven 1 mm screws on the green perimeter of the motherboard.

Step 6

  • Use the plastic opening tool to disconnect the large gold strip underneath the metal plate from the motherboard.

Use the plastic opening tool to disconnect the large gold strip underneath the metal plate from the motherboard.

Step 7

  • Use the plastic opening tool to disconnect the front and back cameras from motherboard.

Use the plastic opening tool to disconnect the front and back cameras from motherboard.

Step 8

  • Use angled tweezers to pry up the black tab.
  • Use the angled tweezers to pull out the gold connector.

Use angled tweezers to pry up the black tab.

Use the angled tweezers to pull out the gold connector.

Step 9

  • Use the angled tweezers to disconnect the gold connector.

Use the angled tweezers to disconnect the gold connector.

Step 10

  • Use the plastic opening tool to disconnect the black connectors on each side of the motherboard.

Use the plastic opening tool to disconnect the black connectors on each side of the motherboard.

Step 11

  • Use the plastic opening tool to lift the motherboard out of place.

Use the plastic opening tool to lift the motherboard out of place.

Step 12

              Front Camera
  • Use the angled tweezers to lift the camera out.

Use the angled tweezers to lift the camera out.

Step 13

              Screen
  • Use the Phillips #00 screwdriver to remove the six 3 mm screws holding the black plastic corner pieces in place.
  • Gently lift the black corner pieces out of the device.

Use the Phillips #00 screwdriver to remove the six 3 mm screws holding the black plastic corner pieces in place.

Gently lift the black corner pieces out of the device.

Step 14

  • Use the angled tweezers to remove the black cables on each side of the device from their groove.

Use the angled tweezers to remove the black cables on each side of the device from their groove.

Step 15

  • Use the plastic opening tool to disconnect the black cable connectors from each side of the device.

Use the plastic opening tool to disconnect the black cable connectors from each side of the device.

Step 16

  • Remove the remaining ten 3 mm Phillips #00 screws.

Remove the remaining ten 3 mm Phillips #00 screws.

Step 17

  • Use the plastic opening tool to disconnect the remaining three gold connectors at the bottom of the device.

Use the plastic opening tool to disconnect the remaining three gold connectors at the bottom of the device.

Step 18

  • Use the plastic opening tool to pry up the grey plastic panel.

Use the plastic opening tool to pry up the grey plastic panel.

Step 19

  • Use the plastic opening tool to pry the screen out of the device.

Use the plastic opening tool to pry the screen out of the device.

Step 20

              Screen Digitizer
  • Use the plastic opening tool to pry the charging board away from the digitizer.

Use the plastic opening tool to pry the charging board away from the digitizer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Jacob Cross

Member since: 01/16/2019

475 Reputation

                                      4 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       University of Alabama, Team S1-G3, Bedsole Spring 2019                        

                                                  Member of University of Alabama, Team S1-G3, Bedsole Spring 2019 



                    UA-BEDSOLE-S19S1G3                     


                                            4 Members                     


                                            6 Guides authored