Avertx Hd810 Ir Led Lightboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          4 - 10 minutes

Sections

Clear Dome Cover
3 steps
IR LED Lightboard
2 steps

Flags

BackAvertX HD810
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Clear Dome Cover

Lift off the paintable snap-on cover from the AvertX HD810 dome security camera.
Optimally, the device should be turned off and the PoE (Power over Ethernet) unplugged.

Lift off the paintable snap-on cover from the AvertX HD810 dome security camera.

Optimally, the device should be turned off and the PoE (Power over Ethernet) unplugged.

1024

Step 2

Loosen both 10mm screws on either side of the clear dome cover housing using a T10 Torx security screwdriver.
It is not recommended to remove the screws from the clear dome cover housing. The screws are apart of the cover and not intended to come out.

Loosen both 10mm screws on either side of the clear dome cover housing using a T10 Torx security screwdriver.

It is not recommended to remove the screws from the clear dome cover housing. The screws are apart of the cover and not intended to come out.

Step 3

Gently pull off the clear dome cover from the camera base.

Gently pull off the clear dome cover from the camera base.

Step 4

              IR LED Lightboard

Use the PH1 screwdriver to remove or loosen both 10mm screws on either side of the inner protective lens cover. This will loosen both the cover and the IR LED lightboard.
The cover and the lightboard are two separate pieces held in place by these two screws. The cover should be set aside first before continuing with the lightboard.

Use the PH1 screwdriver to remove or loosen both 10mm screws on either side of the inner protective lens cover. This will loosen both the cover and the IR LED lightboard.

The cover and the lightboard are two separate pieces held in place by these two screws. The cover should be set aside first before continuing with the lightboard.

Step 5

Pull the IR LED light board gently away from the camera to expose the connecting cable.
Firmly but gently detach the IR lED light board from its cable connector by pulling directly away from the connection port.
A spudger may be used to loosen a stubborn cable connection. Wedge the flat end of the spudger between the connector and the port to ease it off of the port’s prongs.

Pull the IR LED light board gently away from the camera to expose the connecting cable.

Firmly but gently detach the IR lED light board from its cable connector by pulling directly away from the connection port.

A spudger may be used to loosen a stubborn cable connection. Wedge the flat end of the spudger between the connector and the port to ease it off of the port’s prongs.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Luke Browning

Member since: 01/18/2017

316 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Eastern Washington University, Team 2-3, Crane Winter 2017                        

                                                  Member of Eastern Washington University, Team 2-3, Crane Winter 2017 



                    EWU-CRANE-W17S2G3                     


                                            3 Members                     


                                            10 Guides authored

Toy Camry - Sep 15, 2019

Hi Luke, do you know of a source for parts (IR LED Board, Motherboard etc…) for this AvertX HD810 camera ? Thanks for the great writeup, Toy

Introduction#

What you need#

Team#

Introduction

What you need

Team