Difficulty

Moderate

Steps

5

Time Required

                          15 minutes

Sections

1

  • Front Cover/ Keypad
  • 5 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackAVM Fritz!Fon C5

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The front can also be found on Ebay under the keyword “FritzFon C5 front”

What you need

Step 1

              Back panel and battery removal
  • Loosen the back panel using your fingernail/ guitar pick or a spudger.
  • Slide the pick all around the housing until the back panel comes off.
  • Once it’s off simply remove the battery from the housing.

Loosen the back panel using your fingernail/ guitar pick or a spudger.

Slide the pick all around the housing until the back panel comes off.

Once it’s off simply remove the battery from the housing.

1024

Step 2

              Loosen Housing
  • Loosen the 8 T5 screws, and set them aside.
  • The upper shell / front of the housing consists of filigree bars around the keypad, so special care is required here. In my case, some of these were already broken.
  • Move the opening pick / spudger around the case, lifting off the tabs (orange) with a flat screwdriver. This is done through the corresponding openings in the middle part of the housing (green).

Loosen the 8 T5 screws, and set them aside.

The upper shell / front of the housing consists of filigree bars around the keypad, so special care is required here. In my case, some of these were already broken.

Move the opening pick / spudger around the case, lifting off the tabs (orange) with a flat screwdriver. This is done through the corresponding openings in the middle part of the housing (green).

Step 3

              PCB removal
  • The circuit board can then be easily removed together with the keypad.
  • Replace the parts to be repaired and screw them back together.

The circuit board can then be easily removed together with the keypad.

Replace the parts to be repaired and screw them back together.

Step 4

              Speaker and Display Window
  • Loudspeaker (yellow) and screen protector (green) are glued on and can be easily lifted out with a flat screwdriver.
  • A transparent piece of plastic (light blue), which was probably used to align the loudspeaker, was no longer needed, nor was I able to take over the piece of fabric (red) in front of the loudspeaker.
  • The keypad got hooked in a few places, so I had to rework the associated openings with a file.

Loudspeaker (yellow) and screen protector (green) are glued on and can be easily lifted out with a flat screwdriver.

A transparent piece of plastic (light blue), which was probably used to align the loudspeaker, was no longer needed, nor was I able to take over the piece of fabric (red) in front of the loudspeaker.

The keypad got hooked in a few places, so I had to rework the associated openings with a file.

Step 5

              Assembly
  • Put everything back together in reverse order - make sure that the buttons do not get stuck.

Put everything back together in reverse order - make sure that the buttons do not get stuck.

Reverse the steps to reassemble your device.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

oldturkey03

Mariah Adams

Extreme Experiments

Annika Faelker

Author

                                      with 1 other contributor 


                    Peter Scholl

Member since: 06/26/2021

1,031 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

James - Oct 25, 2021

Reply

Yea please cam you help me

Peter Scholl - Oct 25, 2021

I can’t say without knowing your question/problem.

H. Zapf - Jan 2, 2022

Reply

Ich finde auf eBay aktuelle keine 3D gedruckten C5 Oberschalen. Können Sie mir einen Tipp geben, wo man so etwas erhält?

Peter Scholl - Jan 3, 2022

Reply

Hallo - da kann ich leider nichts zu sagen, da ich meine Oberschale selbst gedruckt habe. Ich habe auch keine Erfahrung wie es ist, wenn man einen solchen Druck in Auftrag gibt - falls Sie da Erfahrung sammeln, fände ich eine kurze Info auch interessant. Viel Erfolg!

M O - Feb 19, 2022

Hallöle, kannst du die 3D zur Verfügung stellen.

Grüße