Difficulty
Moderate
Steps
8
Time Required
10 - 15 minutes
Sections
1
- Subwoofer
- 8 steps
Flags
0
BackAxess SPBT1031
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Subwoofer
- Look at the side of the speaker without the red interface plate; there will be a red ring around the mesh but no buttons on the side.
- Remove the two 5.5 mm screws from the top and bottom of the black face plate using a Phillips #1 screwdriver.
- Do not remove the plate yet.
Look at the side of the speaker without the red interface plate; there will be a red ring around the mesh but no buttons on the side.
Remove the two 5.5 mm screws from the top and bottom of the black face plate using a Phillips #1 screwdriver.
Do not remove the plate yet.
1024
Step 2
- Use a metal spudger to remove the mesh speaker cover by wedging the narrow end into the center of the outer edge of the mesh touching the red plate.
Use a metal spudger to remove the mesh speaker cover by wedging the narrow end into the center of the outer edge of the mesh touching the red plate.
Step 3
- Remove four 5.5 mm screws from the red panel under the mesh using a Phillips #1 screwdriver.
- For subwoofer replacement there will be four screws to remove and four bolts as well. The bolts are used for alignment and cannot be removed.
Remove four 5.5 mm screws from the red panel under the mesh using a Phillips #1 screwdriver.
For subwoofer replacement there will be four screws to remove and four bolts as well. The bolts are used for alignment and cannot be removed.
Step 4
- If the screws are difficult to remove, use the tweezers to twist and pick them out.
If the screws are difficult to remove, use the tweezers to twist and pick them out.
Step 5
- Separate the red plate from the black face plate by removing the black plate from the tube and pushing on the inside of the subwoofer.
- Be careful not to damage the black face plate or red plate as you pull them apart.
- You may place the black faceplate back on the tube, but do not screw it back in yet.
Separate the red plate from the black face plate by removing the black plate from the tube and pushing on the inside of the subwoofer.
Be careful not to damage the black face plate or red plate as you pull them apart.
You may place the black faceplate back on the tube, but do not screw it back in yet.
Step 6
- To remove the the wires from the subwoofer terminals, use a soldering iron to reheat the solder at each of the four points of connection.
To remove the the wires from the subwoofer terminals, use a soldering iron to reheat the solder at each of the four points of connection.
Step 7
- Use a desoldering pump to remove the liquid solder from the terminals.
Use a desoldering pump to remove the liquid solder from the terminals.
Step 8
- Remove the old subwoofer.
- Connect the brown wires to the positive terminals and the black ones to the negative terminals when re-soldering.
Remove the old subwoofer.
Connect the brown wires to the positive terminals and the black ones to the negative terminals when re-soldering.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 7 other contributors
Elvira Lou Evangelista
Member since: 03/09/2016
950 Reputation
6 Guides authored
Badges:
16
+13 more badges
Team
UMass Dartmouth, Team 8-6, Botvin Spring 2016
Member of UMass Dartmouth, Team 8-6, Botvin Spring 2016
UMASSD-BOTVIN-S16S8G6
3 Members
8 Guides authored
Ramon lopez - Dec 4, 2016
Reply
I Ned to replace the charger conection and I need the parts please u can email me at elpaleterolopez@Gmail.com or call me at 6613402547
