Difficulty

Moderate

Steps

10

Time Required

                          5 - 10 minutes

Sections

2

  • Back Cover
  • 4 steps
  • Speaker
  • 6 steps

Flags

0

  • BackAxess TA2513-10WT

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Lay the tablet down on a flat surface with the screen facing up, and the external camera facing upwards and closest to you.

Lay the tablet down on a flat surface with the screen facing up, and the external camera facing upwards and closest to you.

1024

Step 2

  • Insert the plastic opening tool in the space between the screen and the back cover above the volume buttons.
  • Slide the plastic opening tool gently along the sides.
  • If a small gap is not created between the screen and the back cover, pry gently upward at each of these latching points.

Insert the plastic opening tool in the space between the screen and the back cover above the volume buttons.

Slide the plastic opening tool gently along the sides.

If a small gap is not created between the screen and the back cover, pry gently upward at each of these latching points.

Step 3

  • Place the spudger in an open space to keep the back case from shutting while you continue to slide the opening tool.

Place the spudger in an open space to keep the back case from shutting while you continue to slide the opening tool.

Step 4

  • Remove the back cover with your hands once all points have been unlatched. It should separate completely from the screen that contains the battery and chip components.

Remove the back cover with your hands once all points have been unlatched. It should separate completely from the screen that contains the battery and chip components.

Step 5

              Speaker
  • Remove tape attached to black and red speaker wires.

Remove tape attached to black and red speaker wires.

Step 6

  • Identify the four speaker nodes.
  • From left to right the nodes are “SPKP1”, “SPKN1”, “LN”, and “LP”

Identify the four speaker nodes.

From left to right the nodes are “SPKP1”, “SPKN1”, “LN”, and “LP”

Step 7

  • Place the soldering tool on the speaker node labeled “SPKP1” and quickly remove the red wire with tweezers.

Place the soldering tool on the speaker node labeled “SPKP1” and quickly remove the red wire with tweezers.

Step 8

  • Place the soldering tool on the speaker node labeled “SPKN1” and quickly remove the black wire with tweezers.

Place the soldering tool on the speaker node labeled “SPKN1” and quickly remove the black wire with tweezers.

Step 9

  • Place the soldering tool on the speaker node labeled “LP” and quickly remove the black wire with the tweezers.

Place the soldering tool on the speaker node labeled “LP” and quickly remove the black wire with the tweezers.

Step 10

  • Place the soldering tool on the speaker node labeled “LN” and quickly remove the red wire with tweezers.

Place the soldering tool on the speaker node labeled “LN” and quickly remove the red wire with tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 7 other contributors 


                    Steven Kavanagh

Member since: 03/24/2015

301 Reputation

                                      3 Guides authored                  



                       Badges:
                       3

Team

                       Baylor, Team 6-3, Shaver Spring 2015                        

                                                  Member of Baylor, Team 6-3, Shaver Spring 2015 



                    BU-SHAVER-S15S6G3                     


                                            3 Members                     


                                            10 Guides authored